Torque Freaks dyno special $29.99 for 3 pulls

[86strokerlx]

Hey everyone! This is Mike with Torque Freaks. www.torquefreaks.com Just wanted to let you know that our shop Torque Freaks in Portland is having a baseline dyno (3 pulls) special for $29.99. If you want us to us the wideband O2 sensor, add another $10. We're doing this untill further notice. Most likely untill the end of September. Feel free to call or email to inquire about an appointment. Our usual pricing is as follows:

Baseline 3 pulls(no manipulation): $65.00
Same as above plus wideband(a/f): $75.00

Lease dyno(you tune): $85.00/Hour
Same as above plus air/fuel: $95.00/Hour

Dyno Day w/ 8 or more cars: $50.00 per vehicle

If interested in dynoing a deisel vehicle, we can also do that. Please inquire regarding cost. Please be sure to mention you read about it on Stangnet!

Thanks! Mike [email protected]

Torque Freaks Inc.
12903 NE Airport Way
Portland, OR 97230
503.256.5600 ext. 2

Service Manager: [email protected]
Sales and Appointments: [email protected]

 

[Tylerb59]

 

[gospeedgo]

Freakin sweet! Were gonna have to load up the stock car and make ohh....about 3 pulls Just gotta fugure out how to pull the stagger out of it first

 

[Mega-Man]

Why oh why couldn't you be in WA State?!!!

I love it when places hit the boards to connect to their customers--kudos--and lucky you Portland folks.

- Mega (who last got quoted $150.00 / hr from a local place just to do baseline testing--sheesh...)

 

[saleenster]

Why oh why couldn't you be in WA State?!!!

I love it when places hit the boards to connect to their customers--kudos--and lucky you Portland folks.

- Mega (who last got quoted $150.00 / hr from a local place just to do baseline testing--sheesh...)

Well...they are pretty much there as it's just a 5 minute drive from I-205 bridge and their shop...if that. For $30 bucks we are gonna keep them quite busy....

 

[ZeroCool]

When we hooking up to go? I'm dying to find out what my new motor has in it.

 

[The Factor]

When we hooking up to go? I'm dying to find out what my new motor has in it.

I'LL go with ya too Jerry I want to take a few more dyno runs and do some dialing in

 

[saleenster]

I'LL go with ya too Jerry I want to take a few more dyno runs and do some dialing in

I would love to go sometime next wk..only I need to see if Jeff can roll along for a little "tweaking"

 

[saleenster]

I'LL go with ya too Jerry I want to take a few more dyno runs and do some dialing in

Ed, dont forget to bring the "louie factor" with ya

 

[ZeroCool]

Ya'll let me know when you want to go, maybe I can get a day off of work...

 

[ddonaca351]

figures, I wreck my ride and you guys are going to be having a dyno-fest for the next monthe while its in the shop....

MURPHY WAS AN OPTOMIST !!!!!!





Oh well, mine will be prettier than yours

DD

 

[hicalibrbulit]

I'd like in on that too!

 

[The Factor]

Ed, dont forget to bring the "louie factor" with ya

Cory the Ed Louie factor will always be along for the ride. looking foward to hanging out again Cory.

 

[jordanvraptor]

Hmmm, I might roll out there and get a STOCK baseline... I'll probably wait and see what it does with stock intake and exhaust AND a pulley... Cause that's gonna be my setup for a while.

 

[Scooby5.0Doo]

i plan on going soon too just top see the a/f and wether or not i need to play with the fuel press.

 

[86strokerlx]

$30 for three dyno pulls. $10 additional for A/F.

I'm happy to see that there is some interest! We need more Domestics coming down to the shop! Seeing a Supra put down 700rwhp on stock internals is great but I LOVE the roar and the feel of a V8! Hope to see everyone down there soon! www.torquefreaks.com

Our standard pricing:

Baseline 3 pulls(no manipulation): $65.00
Same as above plus wideband(a/f): $75.00

Lease dyno(you tune): $85.00/Hour
Same as above plus air/fuel: $95.00/Hour

Dyno Day w/ 8 or more cars: $50.00 per vehicle

Please be sure to mention you read about it on Stangnet!

Thanks! Mike [email protected]

Torque Freaks Inc.
12903 NE Airport Way
Portland, OR 97230
503.256.5600 ext. 2

Service Manager: [email protected]
Sales and Appointments: [email protected]

 

[Black 93 Fox]

Im gona go this coming week sometime or next week. Be cool if all of us could go at the same time like last time.

Andy

 

[86strokerlx]

just give us a call or shoot an email to set up a time, day or what have you.
www.torquefreaks.com

Torque Freaks Inc.
12903 NE Airport Way
Portland, OR 97230
503.256.5600 ext. 2

[email protected]
[email protected]

 

[jordanvraptor]

Now when you say baseline....? Does that mean its a one per customer kind of deal or can we come back for the same price if say we added a new pulley...?

 

[gospeedgo]

By baseline, they mean you make 3 passes and are done, you arent tuning at the same time. They dont want you sitting there on your laptop programming the chip between runs, just make 3 passes for numbers. For tuning, you rent the dyno for a per hour rate