• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

TPS voltage help

  • Thread starter Thread starter theconductor
  • Start date Start date Nov 1, 2007

theconductor

15 Year Member
Aug 9, 2007
337
96
74
Roseville, CA
Nov 1, 2007
#1
  • Nov 1, 2007
  • #1
I put on a new tps and I am trouble getting the voltage under 1.0. I assume that I just need to make one of the holes bigger for more adjustment, then again I really don't know that much!

Any ideas for help?

Thanks,

Kyle
 

Gearbanger 101

Straight Outta Locash
20+ Year Stangneter
Aug 10, 2002
9,457
1,377
234
Ontario, Canada
Nov 1, 2007
#2
  • Nov 1, 2007
  • #2
Correct. You may need to elongate the holes slightly with a small file to increase the adjustable range. Try to shoot for as close to 1.0V as possible, without going over. Generally .98-.99V is acceptable.

Nice little tech read on how to....

Summary:

What is the TPS?

Sitting on top of your throttle body there is a sensor that relays to the computer the exact opening position of the throttle butterfly. In other words, how far do you have your foot into the accelerator pedal. In technical terms the TPS is a low-voltage potentiometer. Based on the position of the throttle and other factors given to it, the computer will decide how rich the fuel mixture will be at any given open throttle point.


Why mess with the TPS?

Well, based on the information given above it is easy to understand how important this sensor is to your Mustang's performance. It is important that the computer gives the correct air and fuel mixture at the right time. If your TPS is off (or bad), the information (voltage) that the computer gets will be inaccurate. The tuning procedures in this article are very simple and the potential for the TPS to be off is significant, so why not tune your car the right way and get the most out of it.

Details:

Tuning the TPS

When you tune up your Mustang (wires, plugs, timing, etc.), the checking/adjustment (if needed) of the TPS should always be included. You will need a Phillips screwdriver, a pin, and a voltmeter that can read low voltages accurately. Here is the procedure:

1) Loosen the two screws holding on the TPS, (The screws can be very stubborn, so make sure you have a good quality screw driver that fits snug and has a long handle for lots of torque, or you might strip the heads) just enough to able to swivel the TPS with force.
2) Pierce the "GREEN" wire with the pin and hook the positive (+) lead from the voltmeter to it.
3) Ground the negative (-) lead from the voltmeter. Use a good ground, like the engine or other grounded metal source.
4) Turn your ignition key to the run position, but do not start the vehicle
5) Rotate the TPS until you achieve .98 to .99 Volts (For stock or slightly modified engines).
6) Tighten the screws on the TPS and recheck.

Troubleshooting

If the maximum or minimum voltage you can obtain is close to the above recommended voltage setting (.98-.99), but the TPS just won't turn enough to get it right, you will have to modify the TPS. If you get a very low voltage reading, make sure you have an accurate voltmeter and your connections are solid, if so, you need to replace your TPS. If you have no voltage, you have a bad connection or a bad voltmeter. Rarely, if never, will a TPS be in such bad shape, especially if your car still runs good.
Click to expand...
 

bloopbloob

Member
Sep 27, 2006
578
4
16
Alberta
Nov 1, 2007
#3
  • Nov 1, 2007
  • #3
yup! probably both if they are lined up properly though. either way, just elongate the holes if you have to and you should be good.

edit: screw the file! i just used a drill bit, took 2 seconds. apparently .985V is "perfect" but a lot argue that it doesnt really matter as long as you're in a certain range from idle to FT.... i dont know personally, so i just set mine to exactly .985, and it works well for me
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Nov 1, 2007
#4
  • Nov 1, 2007
  • #4
If it was me, I would not mangle a new TPS as long as the reading was under about 1.20 volts. The puter should baseline the reading if it's within the adaptive ability anyhow.

Just MHO.
Good luck.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Nov 1, 2007
#5
  • Nov 1, 2007
  • #5
Since the computer zeros out the TPS voltage every time it powers up, playing with the settings isn't an effective aid to performance or driveablity. The main purpose of checking the TPS is to make sure it isn't way out of range and causing problems.

Setting the TPS: you'll need a good Digital Voltmeter (DVM) to do the job. Set the TPS voltage at .5- 1.1 range. Because of the variables involved with the tolerances of both computer and DVM, I would shoot for somewhere between .6 and 1.0 volts. Unless you have a Fluke or other high grade DVM, the second digit past the decimal point on cheap DVM’s is probably fantasy.

The Orange/White wire is the VREF 5 volts from the computer. You use the Dark Green/Lt green wire (TPS signal) and the Black/White wire (TPS ground) to set the TPS. Use a pair of safety pins to probe the TPS connector from the rear of the connector. You may find it a little difficult to make a good connection, but keep trying. Put the safety pins in the Dark Green/Lt green wire and Black/White wire. Make sure the ignition switch is in the Run position but the engine isn't running.

Here’s a TPS tip I got from NoGo50

When you installed the sensor make sure you place it on the peg right and then tighten it down properly. Loosen the back screw a tiny bit so the sensor can pivot and loosen the front screw enough so you can move it just a little in very small increments. I wouldn’t try to adjust it using marks.

(copied from MustangMax, Glendale AZ)

A.) Always adjust the TPS and Idle with the engine at operating temp. Dive it around for a bit if you can and get it nice and warm.

B.) When you probe the leads of the TPS, do not use an engine ground, put the ground probe into the lead of the TPS. You should be connecting both meter probes to the TPS and not one to the TPS and the other to ground.

C.) Always reset the computer whenever you adjust the TPS or clean/change any sensors. I just pull the battery lead for 10 minutes.

D.) The key is to adjust the TPS voltage and reset the computer whenever the idle screw is changed.
 

theconductor

15 Year Member
Aug 9, 2007
337
96
74
Roseville, CA
Nov 1, 2007
#6
  • Nov 1, 2007
  • #6
Thanks for all of the great information. I will mess with it until I get it down tonight after work.

HISSIN50 said that the voltage doesn't have to be under 1 volt. I thought that I read somewhere that at 1 volt or over the computer reads as WOT. Maybe I am dreaming.... That's why I have you guys on here, to set me straight!


Kyle
 

ShortThrow50

Member
Oct 22, 2006
923
2
16
Pa
Nov 1, 2007
#7
  • Nov 1, 2007
  • #7
HISSIN50 said:
If it was me, I would not mangle a new TPS as long as the reading was under about 1.20 volts. The puter should baseline the reading if it's within the adaptive ability anyhow.

Just MHO.
Good luck.
Click to expand...

Finally, someone who agrees with me
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Nov 1, 2007
#8
  • Nov 1, 2007
  • #8
theconductor said:
HISSIN50 said that the voltage doesn't have to be under 1 volt. I thought that I read somewhere that at 1 volt or over the computer reads as WOT. Maybe I am dreaming.... That's why I have you guys on here, to set me straight!


Kyle
Click to expand...

Someone might have said that but if he/she did, he/she is an idiot.

The computer sees ~2.71 volts over the baseline reading as WOT. Said another way, the puter sees approximately 3.70 TPS volts as WOT.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Nov 1, 2007
#9
  • Nov 1, 2007
  • #9
As long as you don't get a code for the TPS being 'out of range'
you are good.

Adjusting to .98v to .99v does nothing for you.

'Tuning' the TPS seems to be a Myth that started in EEC-II or -III vehicles.... (I don't recall exactly...)
Regardless... 'Tuning' the TPS is a waste of time for our EEC-IV cars...

Just check it to make sure you are within .6v to 1.2v (IIRC), the EEC-IV acceptable range.
And, as always, pull the codes...

jason
 

theconductor

15 Year Member
Aug 9, 2007
337
96
74
Roseville, CA
Nov 2, 2007
#10
  • Nov 2, 2007
  • #10
I have it a 1.0xx so I guess that I'll leave it. Sounds good to me, the less stuff to adjust the better.

Thanks again.


Kyle
 

5.0Torx

Active Member
Dec 30, 2007
252
3
29
Feb 14, 2008
#11
  • Feb 14, 2008
  • #11
my engine usually revs up 100-200 rpm between shifts unless i compensate for it by letting off the gas a split second before clutching in. is that TPS-related?
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Feb 14, 2008
#12
  • Feb 14, 2008
  • #12
5.0Torx said:
my engine usually revs up 100-200 rpm between shifts unless i compensate for it by letting off the gas a split second before clutching in. is that TPS-related?
Click to expand...
Probably not....
More likely to be related to the VSS, if it's sensor related at all...


Pull the diagnostic codes and see what you get.


jason
 
You must log in or register to reply here.

Similar threads

M
Fox Random spike voltage (Need help from scope users)
  • martroy
  • Sep 28, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
20
Views
519
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 27, 2026
martroy
M
R
TPS
  • Redguy69
  • May 5, 2025
  • 1994 - 1995 Specific Tech
Replies
1
Views
163
1994 - 1995 Specific Tech May 5, 2025
Noobz347
G
Resolved Smoking Wiring Issue After GT40 Head Swap
  • Grapes
  • Aug 15, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
593
Fox 5.0 Mustang Tech Aug 22, 2026
Grapes
G
A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
594
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
405
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?