Trick Flow kit - why no 94 - 95s?

gcomfx.com · Apr 19, 2006

Why does the Track Heat kit say: This kit will not work on 1994-95 Ford Mustangs. It's only $50 more and it has the better intake right?

http://store.summitracing.com/partd...8+4294908331+4294840126+1011+115&autoview=sku

urban96 · Apr 19, 2006

only difference i know of is the intake elbow

gcomfx.com · Apr 19, 2006

That's what I thought, but the other kit, with the base intake doesn't come with the elbow either.

mackey · Apr 19, 2006

You need a 3/8" spacer on the intake or else the elbow will not fit.

drakesdad · Apr 19, 2006

I have the Track Heat......needed the spacer and the elbow........

drakesdad · Apr 19, 2006

The spacer and elbow are under 200.00 combined...don't remember because I did not order the spacer and ended up getting it for free.........I am very happy with the set up but you will need some tuning of 'course....lol good luck

1990Coupe · Apr 19, 2006

Or you could just do the fox swap???

Killercanary · Apr 19, 2006

JFYI- Yeahloh95 is selling his track heat with a spacer and the inlet elbow.

94opalgt · Apr 19, 2006

you also have to remove hood blanket,it will rub the intake in the front on the drivers side.mine did.also had to use the spacer

gcomfx.com · Apr 19, 2006

Interesting... I have the 96 Cobra hood, I wonder what kinds of havoc that might cause. :x

Also, do you have to get longer intake bolts?

94opalgt · Apr 19, 2006

longer bolts come with the spacer.not sure about the hood thing though.should still fit but you might still have to remove the blanket

speedfreek95GT · Apr 19, 2006

I emailed trick flow about the same thing....they told me all i needed was an intake spacer, elbow adapter for the t/b and a longer hose for one of the vaccum lines. Here are the part numbers trick flow gave me.......
1) TFS # 5150SN95-00 elbow adapter for the throttle body.
2) TFS # 51520007, upper/lower manifold spacer.
3) You will need to modify the EGR tube to fit.
4) You will need to get a custom computer tune as the 1994-95 computers
are
very finicky.

gcomfx.com · Apr 20, 2006

94opalgt said:
longer bolts come with the spacer.not sure about the hood thing though.should still fit but you might still have to remove the blanket

I've had a whale of a good time with my aftermarket Strut Tower Brace. Fit around the Cobra Intake just fine, but had to have a welder modify it so the hood would close. Just changed my dizzy and it's a 1/4" taller. My coil wire would arc from the center post to the brace, so I had to remove it. Takes some getting used to, to drive the car without that brace.... but it's "okay" I guess.

I figure the hood will have to replaced sooner or later... I like the looks of it, but it's just not very tall where it needs to be. Dang 4.6 motors.

mackey · Apr 20, 2006

"4) You will need to get a custom computer tune as the 1994-95 computers
are
very finicky."

Mine runs fine without it.

gcomfx.com · Apr 20, 2006

Wow, there are a lot more people with this kit than I thought.... tell me some 1/4 times. I would like to know aprox. how much my car would improve.

Trick Flow kit - why no 94 - 95s?

gcomfx.com

urban96

bubb rubb says:"woo woooooo"

gcomfx.com

mackey

Active Member

drakesdad

Member

drakesdad

Member

1990Coupe

Killercanary

The car that set the bar.

94opalgt

Member

gcomfx.com

94opalgt

Member

speedfreek95GT

New Member

gcomfx.com

mackey

Active Member

gcomfx.com

Similar threads

Trick Flow kit - why no 94 - 95s?

bubb rubb says:"woo woooooo"

Active Member

Member

Member

The car that set the bar.

Member

Member

New Member

Active Member

Similar threads

Privacy & Transparency

Privacy & Transparency