• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Turbo on - No oil pressure??

  • Thread starter Thread starter NO_RICE
  • Start date Start date Jun 14, 2008

NO_RICE

Founding Member
May 5, 2001
405
1
16
Tucson, AZ
Jun 14, 2008
#1
  • Jun 14, 2008
  • #1
I finally got my car started again, the problem is that my oil pressure gauge reads below 0 when the car is off and jumps just slightly over zero when the car is started. I have tried several things so far:

- double checked the lines on my oil filter relocation kit

- disconnected the turbo feed line to see if oil was making it to the turbo

- jumpered a ground from the body of the sending unit to the frame

- grounded input wire on the gauge to make sure the gauge works

How often do sending units go bad? It doesn't sound like there is any lack of oil,(valve train noise) but then again I only have a 3' downpipe and Im not sure I would be able to hear it over the exhaust anyway. Are there any other things I should try? I really don't want to just assume everything is ok and have my motor seize on me.

just for kicks heres a picture

 

68FBJJZ109

Member
May 2, 2005
357
0
17
Easton, PA
Jun 14, 2008
#2
  • Jun 14, 2008
  • #2
I can think of anything else to check, if there is no valve train noise and your turbo is getting oil, then you have more then 0 psi or slightly above it. I believe a turbo only needs like 20-25 psi of oil pressure to supply itself, thats a indication if your getting oil to the turbo. how much is a oil pressure sending unit? its prob worth just swapping it out to see if it reads the same, take it back. i went with a manual oil pressure gauge. and ditched the stock gauge cluster because i had issues from before i turboed mine.
 

68FBJJZ109

Member
May 2, 2005
357
0
17
Easton, PA
Jun 14, 2008
#3
  • Jun 14, 2008
  • #3
Also you may want to get a turbo blanket, or a heat shield. if you have no plans of moving it. My turbo is in roughly the same spot and fried my bearings in the alternator. My buddy is currently swapping it over to the other side for my since i am not in PA currently.
 

2000xp8

SN Certified Technician
Aug 8, 2003
8,029
1,621
194
NJ
Jun 14, 2008
#4
  • Jun 14, 2008
  • #4
Get a mechanical oil pressure gauge. Try to get a full sweep gauge, they are a bit easier to read.
Heavily modified cars need real gauges for water temp and oil pressure.
 

NO_RICE

Founding Member
May 5, 2001
405
1
16
Tucson, AZ
Jun 14, 2008
#5
  • Jun 14, 2008
  • #5
I have the 3 gauge pillar, with electric autometer gauges, I am going to get a factory replacement sending unit and reconnect the factory gauge just to see if I really do have oil pressure, then I will order a new sending unit for my autometer gauge. I hate to use a manual gauge because I don't like the idea of having oil spill inside the car
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 14, 2008
#6
  • Jun 14, 2008
  • #6
The stock sender (for a 94-95 GT) reads in the middle if you have more than 6 PSI and it reads zero if you have less. Don't bother with it or any interpolation of it.

As noted, I would grab a $15 mech gauge just to hook up under the hood for diagnostics (it'll just sit on top of the engine bay while you figure out what's going on).

I'd drop you off a spare mech gauge but I can't find any right now (I cleaned the garage awhile back ).
 

2000xp8

SN Certified Technician
Aug 8, 2003
8,029
1,621
194
NJ
Jun 14, 2008
#7
  • Jun 14, 2008
  • #7
NO_RICE said:
I have the 3 gauge pillar, with electric autometer gauges, I am going to get a factory replacement sending unit and reconnect the factory gauge just to see if I really do have oil pressure, then I will order a new sending unit for my autometer gauge. I hate to use a manual gauge because I don't like the idea of having oil spill inside the car
Click to expand...

I understand the concern for oil in the car, but you just have to buy a better line than the plastic one that comes with the gauge.
Me personally, i don't trust gauges with sending units.
 

NO_RICE

Founding Member
May 5, 2001
405
1
16
Tucson, AZ
Jun 15, 2008
#8
  • Jun 15, 2008
  • #8
HISSIN50 said:
The stock sender (for a 94-95 GT) reads in the middle if you have more than 6 PSI and it reads zero if you have less. Don't bother with it or any interpolation of it.

As noted, I would grab a $15 mech gauge just to hook up under the hood for diagnostics (it'll just sit on top of the engine bay while you figure out what's going on).

I'd drop you off a spare mech gauge but I can't find any right now (I cleaned the garage awhile back ).
Click to expand...

I took my fuel pressure gauge off and put it where the sending unit was, it read 45 psi at idle, so Im happy now, I might just buy a mechanical gauge since it is only about $15 more than a new sending unit.

I just need to fabricate the piping from the downpipe to the h pipe and I can get this thing back on the road, passing emissions might be a little tricky, but it has all the emissions equipment, so as long as it passes the sniffer I should be good to go.
 
You must log in or register to reply here.

Similar threads

P
Weird Voltage & Oil Pressure Gauges
  • PNN
  • May 22, 2026
  • SN95 V6 Mustang Tech
Replies
0
Views
59
SN95 V6 Mustang Tech May 22, 2026
PNN
P
B
Engine Strange Noise
  • burntokita
  • May 8, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
403
Fox 5.0 Mustang Tech May 11, 2026
keel
D
Fuel Erratic Fuel Pressure 1985 GT
  • DienstXIV
  • Jan 14, 2026
  • Fox 5.0 Mustang Tech
Replies
16
Views
693
Fox 5.0 Mustang Tech Jan 16, 2026
AeroCoupe
Forced Induction Vortech impeller speed
  • Dontknowchit
  • Aug 6, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
692
Fox 5.0 Mustang Tech Aug 8, 2025
Dontknowchit
Electrical Issues with my 2006 mustang gt
  • VerneVdV
  • May 22, 2026
  • 2005 - 2009 Specific Tech
Replies
0
Views
90
2005 - 2009 Specific Tech May 22, 2026
VerneVdV
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?