Uh oh, Time for a new Rack&Pinion and PS Pump??

MSM0075

Member

May 13, 2003

741

0

16

Central Jersey

Dec 26, 2003

#1

• Dec 26, 2003

• #1

I was crusin' around with "50mustang001" a couple weeks ago and on our way back home we noticed a real loud whiney noise like the powerstearing noise got louder than it already was. Got it back to his house and noticed the power stearing pump was empty, uh oh! So I quickley filled it up and drove it home. Its leaking from the inner part of the boot on the rack..Leaks up to a pint a day..Its slowed down latley though. The pump was loud to begin with. If I have to add a new R&P It would make scence to replace the Pump too beacuse I dont want that warn thing griding up my Rack, correct? Should I just buy pepboys crap? What do you guys think?

 

M

MustangPatty

Founding Member

Jun 5, 2002

292

0

0

Sallisaw OK

Dec 26, 2003

#2

• Dec 26, 2003

• #2

Not too long after I got my '93, actually that day, the Rack went out, just replaced it with a Re-Bult one, un less its leaking, or not working there shouldnt be any reason to replace the pump, i didnt, and never had to put fluid in it again. Though, when you replace the rack, get an alignment, its tough to lign that stuff back up exactly, mine was slightly off.

 

MSM0075

Member

May 13, 2003

741

0

16

Central Jersey

Dec 26, 2003

#3

• Dec 26, 2003

• #3

But if I ran my pump for too long w/o fluid it could have metal shavings in there that could damage my rack..Its the loudest pump I've ever drivin with...Even before It ran out of fluid that one day...

 

i4power

Founding Member

Jan 11, 2002

1,083

0

0

Eglin AFB, Florida

Dec 26, 2003

#4

• Dec 26, 2003

• #4

Replace the stock steering rack with a Flaming River rack and pinion.

 

MSM0075

Member

May 13, 2003

741

0

16

Central Jersey

Dec 26, 2003

#5

• Dec 26, 2003

• #5

Am I reading this wrong? I can only find for Mustang II's

http://www.streetrodengineering.com/flaming river rack-pinion.htm

Should I replace the Pump too?

 

svoman2300

New Member

May 12, 2003

84

1

0

Pompano Beach, Fl

Dec 26, 2003

#6

• Dec 26, 2003

• #6

I would defiantely change the pump also for cheap insurance I think they are only like $30 or so. And it would be a good idea to flush all the lines after the install by leaving the return line off the pump and pumping fluid into a pan until it looks clean.

 

MSM0075

Member

May 13, 2003

741

0

16

Central Jersey

Dec 26, 2003

#7

• Dec 26, 2003

• #7

Ugh, im so depressed...

I got so many things to do on this car like Springs, Shocks, Struts, Rack&Pinion, Power Steering Pump. Along with your preformance upgrades like Poly-bushings, Caster Plates (SP?) and bigger sway bars..but some of these upgrades require an alignment afterwords. I want to purchase and install everything at once, but I don't have enough funds to do so. I WOULD just save up money but the car is in a pretty dangerous state to drive. *sigh*

 

MustangGlx

New Member

Apr 2, 2003

147

0

0

Connecticut

Dec 26, 2003

#8

• Dec 26, 2003

• #8

i recently had to do the rack, p/s pump, and the p/s pressure and return lines on my 83 3.8 vert. if you ran the pump dry for long enough its never going to get any any more quiet, and it will ware out eventually, a lot sooner than if it had been kept full. I would recomend doing it all at once, its just the logical way, because if you do the rack now, and in a couple monts your pump goes your just going to be pissed off, especially if it eats itself up like mine did and grinds apart the insides, and its not like the pump is going to cost you an arm and a leg, i got mine for somewhere in the neiborhood of 30 or 35 bucks. just an easy safty net,thinking ahead cant hurt.

 

The Shape

Founding Member

Jan 11, 2002

2,224

8

49

East ARKANSAS Delta

Dec 29, 2003

#9

• Dec 29, 2003

• #9

I need to replace my pump cause it is whining terribly. My rack doesn't leak however. What about just replacing the pump is there a way to flush the rack so any old fluid or shavings doesn't contaminate the new pump??

 

W

wuzfast

Founding Member

Sep 21, 2000

569

0

16

Dec 30, 2003

#10

• Dec 30, 2003

• #10

When you put the new rack/and or pump on, keep the car up on jack stands. Plug the return port on the pump and let the return line hang off over a pan. Put fluid in the pump but don't start it. Slowly turn the steering wheel lock to lock a couple of times and check the fluid level again. A couple of times should flush out all the old fluid. Reconnect the return line and refill the pump. Do the lock to lock again slowly with the engine OFF watching the fluid level and it will push out all the air in the lines. Start the engine and turn it slowly lock to lock again, (Don't jam it hard at the ends, it's hard on the pump) and you should be ready to drive.

 

MSM0075

Member

May 13, 2003

741

0

16

Central Jersey

Dec 30, 2003

#11

• Dec 30, 2003

• #11

wuzfast said:

When you put the new rack/and or pump on, keep the car up on jack stands. Plug the return port on the pump and let the return line hang off over a pan. Put fluid in the pump but don't start it. Slowly turn the steering wheel lock to lock a couple of times and check the fluid level again. A couple of times should flush out all the old fluid. Reconnect the return line and refill the pump. Do the lock to lock again slowly with the engine OFF watching the fluid level and it will push out all the air in the lines. Start the engine and turn it slowly lock to lock again, (Don't jam it hard at the ends, it's hard on the pump) and you should be ready to drive.

Click to expand...

Wow thanks for the detailed info!
So you say I should just buy a new pump? The leak seems to have slowed down alot. Considering when it was low i'd fill it up with Lucas everytime, guess it finally kicked in after about 3 of 4 bottles of Lucas..Pump is still loud, and if the car is cold and i try and turn the wheel its real stiff. Could I go wrong if I bought a pump now with my old leaking rack???