• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SVT Tech Forum

upgrading vortech v1 98 svt - need opinions!

  • Thread starter Thread starter zb99gt
  • Start date Start date Oct 19, 2009

zb99gt

New Member
Mar 6, 2009
20
0
0
port huron, michigan
Oct 19, 2009
#1
  • Oct 19, 2009
  • #1
hey guys im sorta new to the forums as well as the supercharger scene and i need some help! i have a 98 cobra with a vortech v1. the blower was makin a slight grinding noise so we figured maybe the bearings were starting to go bad or worse, so i had it sent out to vortech in california for them to run through it and see what they think needs to be done. i just got a call from them saying that the bearings were shot, the gear case needed to be replaced, and the gears were pretty well trashed. apparently the bearings were so loose he said they slid right out and didnt even require any heat. They told me it would be around $1000 to repair, or i could just upgrade the head unit to a v2 si-trim for $1200. Is this upgrade well worth the extra $200 or is there a different upgrade i should be doing instead of the v2 si trim? if it matters, the motor has stock internals and is running at 12 psi. Just wanted to see what everyone recomends before i make a decision. thanks guys,
zach
 

fiveohwblow

Official Member
15 Year Member
Jul 21, 2005
2,169
145
155
Oct 20, 2009
#2
  • Oct 20, 2009
  • #2
Go with the V2 IMHO.
 

zb99gt

New Member
Mar 6, 2009
20
0
0
port huron, michigan
Oct 20, 2009
#3
  • Oct 20, 2009
  • #3
fiveohwblow said:
Go with the V2 IMHO.
Click to expand...

yea thats what they talked me into at vortech, i bought the car with all the stuff already done to it but vortech told me that blower is about 9 years old and for the extra couple hundred bucks to go with the v2. so i did lol only this time i got the polished one instead of the satin finish.
 

COBRA90GT

Mustang Master
Sep 22, 2001
6,654
0
87
HOCKEYTOWN ® , MI
Oct 21, 2009
#4
  • Oct 21, 2009
  • #4
Good decision.

Are you going to have it re-tuned by PHP or was that from the previous owner? If you do get it re-tuned, you may want to consider Lidio at Alternative Auto (in Chesterfield) - he's much closer to you (just south on I-94) and is well known for his tuning ability/experience with Vortech.

 

zb99gt

New Member
Mar 6, 2009
20
0
0
port huron, michigan
Oct 21, 2009
#5
  • Oct 21, 2009
  • #5
COBRA90GT said:
Good decision.

Are you going to have it re-tuned by PHP or was that from the previous owner? If you do get it re-tuned, you may want to consider Lidio at Alternative Auto (in Chesterfield) - he's much closer to you (just south on I-94) and is well known for his tuning ability/experience with Vortech.

Click to expand...


pauls tuned it when the previous owner had it. i would def bring it to lidio though if i have to have it retuned. ive heard alot of good stuff about alternative. Will the car need to be retuned for sure with the new blower?
 

fiveohwblow

Official Member
15 Year Member
Jul 21, 2005
2,169
145
155
Oct 21, 2009
#6
  • Oct 21, 2009
  • #6
My preference is to always play it safe when dealing with a motor under pressure. I would take it to him after the new blower for peace of mind if nothing else.

Often times tuners do what the owners want them to do (well, to an extent) and if the owner wants an aggressive tune then thats what you purchased. It is always good to know exactly where your car sits because you put it there. If you were running on the ragged edge its only a matter of time before you lose it all...
 

zb99gt

New Member
Mar 6, 2009
20
0
0
port huron, michigan
Oct 21, 2009
#7
  • Oct 21, 2009
  • #7
fiveohwblow said:
My preference is to always play it safe when dealing with a motor under pressure. I would take it to him after the new blower for peace of mind if nothing else.

Often times tuners do what the owners want them to do (well, to an extent) and if the owner wants an aggressive tune then thats what you purchased. It is always good to know exactly where your car sits because you put it there. If you were running on the ragged edge its only a matter of time before you lose it all...
Click to expand...

ok yea thats probably the smart thing to do just to be sure
 
You must log in or register to reply here.

Similar threads

S
Upgrade Advice on an 89 GT Convertible NJ
  • SteakDad
  • Apr 17, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
883
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 18, 2025
limp
What's your tow rig?
  • LILCBRA
  • May 31, 2026
  • Other Auto Tech
Replies
3
Views
134
Other Auto Tech May 31, 2026
LILCBRA
T
Losing Refrigerant rapidly on my 98 Mustang GT
  • TekoSn95
  • Jun 21, 2025
  • SN95 4.6L Mustang Tech
Replies
8
Views
373
SN95 4.6L Mustang Tech Aug 17, 2025
TekoSn95
T
3
Eight inches is enough for me...
  • 351MooseStang
  • Nov 27, 2025
  • 1974 - 1978 Mustang II Talk & Tech
Replies
5
Views
571
1974 - 1978 Mustang II Talk & Tech Mar 2, 2026
Bullitt347
new :poo: box, may need to hit you guys up for 79-82 info when i fix thIs turd.
  • rednotch
  • Sep 27, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2 3
Replies
40
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 4, 2026
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SVT Tech Forum
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?