• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Urgent Distributor Help Needed!!!!

  • Thread starter Thread starter NKau
  • Start date Start date Mar 24, 2007

NKau

Founding Member
Dec 15, 2001
1,346
0
37
Jefferson, WI
Mar 24, 2007
#1
  • Mar 24, 2007
  • #1
Finally got my freshly built engine dropped in the car, have the tranny, longtubes, and pretty much everything else hooked up........drop in the distributor after getting the motor turned to TDC, and the distributor sits about an 1/8" up off of the block. What could possibley be going on here? I didn't notice this when I primed the engine with my homebuilt priming tool, but even a distributor without the cam gear does the same thing; sits an 1/8" off the block when installed.

What could possibley be going on here? The only thing I can think is that the oil pump drive is somehow too long, or I possibley slid that little clip the holds the pump drive from being pulled up through the distributor opening a little to high, and it's not letting the dizzy drop all the way?

I am stumped and need to get this car out of my friends garage ASAP......anyone have any ideas?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Mar 24, 2007
#2
  • Mar 24, 2007
  • #2
Aftermarket drive shaft?
Aftermarket dizzy?
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Mar 24, 2007
#3
  • Mar 24, 2007
  • #3
sounds to me like a oil pump drive shaft that is 2 long.
 

twolo4u2c2

5 Year Member
Apr 10, 2003
330
6
29
reading, PA
Mar 25, 2007
#4
  • Mar 25, 2007
  • #4
there is a stop washer on the pump shaft when it is installed to keep it from pulling out when the dist in removed and falling in the pan ......You have to tap the dist down(lightly) to slid that washer down the shaft just the first time it is installed.
 

NKau

Founding Member
Dec 15, 2001
1,346
0
37
Jefferson, WI
Mar 25, 2007
#5
  • Mar 25, 2007
  • #5
Alright. I'll try tapping on the 'priming tool' to see if I can knock it down; just pushing on the distributor wasn't enough. I wasn't sure the bottom of the distributor would run into the little clip or not. I actually slid the clip up the shaft a little once I installed it to be sure the shaft couldn't get out.

The oil pump is just a stock replacement melling (included a new pump drive shaft), and the dizzy is factory, so I wouldn't think i should be running into any issues.
 

twolo4u2c2

5 Year Member
Apr 10, 2003
330
6
29
reading, PA
Mar 25, 2007
#6
  • Mar 25, 2007
  • #6
I'd use the dist....the priming tool may push it down to far. just my .02
 

NKau

Founding Member
Dec 15, 2001
1,346
0
37
Jefferson, WI
Mar 25, 2007
#7
  • Mar 25, 2007
  • #7
The priming tool was just another distributor I tore the cam gear off.......it's all good. Got the little clip pushed down by gently tapping the 'tool' with a hammer. Thanks for the help guys.
 

twolo4u2c2

5 Year Member
Apr 10, 2003
330
6
29
reading, PA
Mar 25, 2007
#8
  • Mar 25, 2007
  • #8
you bet.......thats why we are here....:SNSign:
 
You must log in or register to reply here.

Similar threads

B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
533
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
K
Resolved Weird sound coming from a freshly rebuilt 5.0L
  • karhoot
  • Jun 24, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
408
Fox 5.0 Mustang Tech Jun 27, 2026
Mac131
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
503
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
P
Engine Swapping EFI distributor for carb distributor- shaft length is different
  • pindude80
  • Jul 20, 2024
  • Fox 5.0 Mustang Tech
Replies
2
Views
1K
Fox 5.0 Mustang Tech Jul 21, 2024
pindude80
P
8
Engine Rough idle and aggressive sputtering when accelerating
  • 88vertible
  • Aug 13, 2025
  • Fox 5.0 Mustang Tech
Replies
4
Views
1K
Fox 5.0 Mustang Tech Dec 13, 2025
Jarhead67
J
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?