• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

vaccum lines

  • Thread starter Thread starter myslo50
  • Start date Start date Feb 5, 2008

myslo50

Member
Jun 12, 2006
247
3
18
ohio
Feb 5, 2008
#1
  • Feb 5, 2008
  • #1
ive had my explorer intake on for like 2 yrs now. after i installed it the can ran a little rich. i delt with it for now but i was wondering if anyone who has this intake or the cobra intake, could tell me wher they routed there vaccum lines. i want to check them before spring. i got to buy a coil cause it breaks up at 5k.

now i got my tfs1 cam in and its eye watering.
whats a good range for fuel pressure?
could my injectors be too big?....and the maf is calibrated to the injectors
do i need a hot/ cold plug, which one and part #
mods are in the sig
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Feb 6, 2008
#2
  • Feb 6, 2008
  • #2
Do you have Autolite 25's ? If so gap them to .042 and set fuel pressure to 38. Try bumping your timing to 12-14 degrees with the spout out, while driving under a load listen for pinging! If you get a ping back it back down a degree or two. As far a vac. lines go my exploder intake only has the pcv, the brake booster, the fpr, and a boost gauge on it.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 6, 2008
#3
  • Feb 6, 2008
  • #3
Vacuum line connections:
One large vacuum line from the upper front goes to the carbon canister

One large vacuum line from the rear goes to the vacuum tree.

One small line in the front feeds the Smog pump solenoid control valves on the rear of the passenger side wheel well..

One small line in the rear goes to the fuel pressure regulator.

One small line in the rear goes to the EGR suction regulator.

One large line in the rear goes to the PVC valve.

Diagram courtesy of Tmoss & Stang&2birds - Typical Vacuum Routing for a Fox stang 5.0:


See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host) for help on 88-95 wiring http://www.veryuseful.com/mustang/tech/engine/
 

Attachments

  • mustangFoxFordVacuumDiagram.webp
    37.3 KB · Views: 128
You must log in or register to reply here.

Similar threads

Engine Hiccup at full throttle
  • keel
  • Jun 2, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
31
Views
1K
Fox 5.0 Mustang Tech Jul 30, 2026
keel
L
Engine 85 GT Excessive Idle
  • lutzkecj
  • Sep 18, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
372
Fox 5.0 Mustang Tech Sep 21, 2026
86HO5.0
8
M
Engine Unexplainable Exhaust Pop and Gurgle
  • Mrnissen122
  • Feb 14, 2026
  • Fox 5.0 Mustang Tech
Replies
12
Views
848
Fox 5.0 Mustang Tech Feb 18, 2026
Noobz347
First Car, what should I do for power??
  • tunedV6
  • Apr 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
7
Views
456
1996 - 2004 SN95 Mustang -General/Talk- May 4, 2026
580HP*428Cj
5
I
Engine Help requested in identifying how to resolve engine light issue
  • Ianslaney
  • Oct 4, 2026
  • SN95 4.6L Mustang Tech
Replies
1
Views
184
SN95 4.6L Mustang Tech Oct 4, 2026
Bullitt347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?