• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Vacuum Question (Pic inside)

  • Thread starter Thread starter asecretfile
  • Start date Start date Aug 1, 2008
  • 1
  • 2
Next
1 of 2 Next Last

asecretfile

New Member
Feb 11, 2007
228
0
0
Aug 1, 2008
#1
  • Aug 1, 2008
  • #1
When disconnected from the TB, am I supposed to be drawing a vacuum here? its a fairly strong one at that

View attachment 309047

if not what would cause this?

thanks
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Aug 1, 2008
#2
  • Aug 1, 2008
  • #2
That is normal, it is a vacuum line from the plenum area. It may be connected to the solenoid valve for the carbon canister. Since I don't have a Cobra upper manifold, I can't say for sure.



Diagram courtesy of Tmoss & Stang&2birds


See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host) for help on 88-95 wiring Mustang FAQ - Engine Information Everyone should bookmark this site.

Ignition switch wiring
http://www.veryuseful.com/mustang/tech/engine/images/IgnitionSwitchWiring.gif

Fuel, alternator, A/C and ignition wiring
http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

Complete computer, actuator & sensor wiring diagram for 88-91 Mass Air Mustangs
http://www.veryuseful.com/mustang/tech/engine/images/88-91_5.0_EEC_Wiring_Diagram.gif

Vacuum diagram 89-93 Mustangs
http://www.veryuseful.com/mustang/tech/engine/images/mustangFoxFordVacuumDiagram.jpg

HVAC vacuum diagram
http://www.veryuseful.com/mustang/tech/engine/images/Mustang_AC_heat_vacuum_controls.gif

TFI module differences & pinout
http://www.veryuseful.com/mustang/tech/engine/images/TFI_5.0_comparison.gif

Fuse box layout
http://www.veryuseful.com/mustang/tech/engine/images/MustangFuseBox.gif
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Aug 1, 2008
#3
  • Aug 1, 2008
  • #3
this is my oil fill nipple to TB hose...so its normal with the engine running that I have vacuum on the oil filler nipple, even though its disconnected from the TB?
 

MarcMonteverde

New Member
Sep 4, 2006
66
0
0
S@c-ToWn
Aug 2, 2008
#4
  • Aug 2, 2008
  • #4
yeah its normal, its supposed to pull the burned oil into the intake so it doesnt vent to the atmosphere
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Aug 2, 2008
#5
  • Aug 2, 2008
  • #5
MarcMonteverde said:
yeah its normal, its supposed to pull the burned oil into the intake so it doesnt vent to the atmosphere
Click to expand...

I have vacuum the other way though....oil filler nipple drawing in
 

gt40_2003wes

I did sound a wee bit gay there.
Aug 14, 2005
461
2
48
ky
Aug 2, 2008
#6
  • Aug 2, 2008
  • #6
yes u should have vacume that way its just like a gas can without a hole in it so u need air to be in ur valve pans so oil drains properly
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Aug 2, 2008
#7
  • Aug 2, 2008
  • #7
Agreed that it's part of the PCV system (it allows bi-directionality in the system).
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Aug 2, 2008
#8
  • Aug 2, 2008
  • #8
Yes...reconnect it and leave it alone
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Aug 3, 2008
#9
  • Aug 3, 2008
  • #9
Video

Well come to find out that intake hissing I was hearing wasnt actually coming from the throttle body, it was from the oil fill neck to TB, that thing has alot of vacuum too. Odd thing is...when I pull this hose loose, my hanging idle problem goes away

Heres a video



gt.flv - Video - Photobucket - Video and Image Hosting
 

joel5.0

Member
Jun 15, 2004
429
2
18
Puerto Rico
Aug 4, 2008
#10
  • Aug 4, 2008
  • #10
That is way too much vacuum from the oil filler port. You may want to check the PCV valve and make sure the filter/strainer element is installed. Also check if vacuum is present at the filler tube port after temporarily removing the PCV valve from its seat.
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Aug 4, 2008
#11
  • Aug 4, 2008
  • #11
joel5.0 said:
That is way too much vacuum from the oil filler port. You may want to check the PCV valve and make sure the filter/strainer element is installed. Also check if vacuum is present at the filler tube port after temporarily removing the PCV valve from its seat.
Click to expand...

what do you mean by filter/strainer element?
 

joel5.0

Member
Jun 15, 2004
429
2
18
Puerto Rico
Aug 4, 2008
#12
  • Aug 4, 2008
  • #12
#4 below....

 

asecretfile

New Member
Feb 11, 2007
228
0
0
Aug 4, 2008
#13
  • Aug 4, 2008
  • #13
joel5.0 said:
That is way too much vacuum from the oil filler port. You may want to check the PCV valve and make sure the filter/strainer element is installed. Also check if vacuum is present at the filler tube port after temporarily removing the PCV valve from its seat.
Click to expand...

Tried unseating the pcv. With it taken out, the car starts but will not idle with it taken out
 

joel5.0

Member
Jun 15, 2004
429
2
18
Puerto Rico
Aug 4, 2008
#14
  • Aug 4, 2008
  • #14
Replace th PCV valve....... looks like the valve internals are gone (inspect the valve), allowing full manifold vacuum to be applied to the crankcase.
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Aug 4, 2008
#15
  • Aug 4, 2008
  • #15
joel5.0 said:
Replace th PCV valve....... looks like the valve internals are gone (inspect the valve), allowing full manifold vacuum to be applied to the crankcase.
Click to expand...

I got the car to stay running for a minute with the pcv taken out. When I do that the oil filler still has a little vacuum but much much less. Makes no noise and barely enough to even hold my finger on it

 

asecretfile

New Member
Feb 11, 2007
228
0
0
Aug 4, 2008
#16
  • Aug 4, 2008
  • #16
new pcv same thing
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Aug 4, 2008
#17
  • Aug 4, 2008
  • #17
I can take the PCV out completely, and hold one hand over the PCV hole in lower and the other hand oil fill nipple and when I block off PCV hole, filler nipple pulls vacuum. Block off filler nipple and PCV hole pulls vacuum...pretty strong one. Again this is with manifold vacuum completely taken loose and capped off to test.
 

joel5.0

Member
Jun 15, 2004
429
2
18
Puerto Rico
Aug 5, 2008
#18
  • Aug 5, 2008
  • #18
PCV valve off and vacuum line capped.... and you still have vacuum in the crankcase?
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Aug 5, 2008
#19
  • Aug 5, 2008
  • #19
joel5.0 said:
PCV valve off and vacuum line capped.... and you still have vacuum in the crankcase?
Click to expand...

yea

I took off pcv, capped off the line going into the upper...capped off the hole in the lower that it sits in and still have crankcase vacuum

 

joel5.0

Member
Jun 15, 2004
429
2
18
Puerto Rico
Aug 5, 2008
#20
  • Aug 5, 2008
  • #20
View attachment 308689... the only way I think that would be possible is, if there's a vacuum leak in the lower intake gaskets
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

Mustang II 4 cyl gear hunting and possibly messed up vacuum system
  • oesterreicher
  • May 31, 2026
  • 1974 - 1978 Mustang II Talk & Tech
Replies
11
Views
577
1974 - 1978 Mustang II Talk & Tech Jun 14, 2026
manicmechanic007
P
Vacuum
  • ProTechAutoServices
  • Aug 1, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
336
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 2, 2026
Noobz347
G
Idle surging after warm up
  • GALLY3309
  • Jun 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
253
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 10, 2026
Noobz347
Engine Code 41 again
  • Creomod
  • Jul 7, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
839
Fox 5.0 Mustang Tech Jul 11, 2026
Mcmahst
P
I need definitive heater valve and AC expansion valve answers
  • PurAU
  • Sep 26, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
4
Views
245
1965 - 1973 Classic Mustangs -General/Talk- Oct 1, 2026
GypsyR
G
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?