• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Vacuum Question (Pic inside)

  • Thread starter Thread starter asecretfile
  • Start date Start date Aug 1, 2008
Prev
  • 1
  • 2
First Prev 2 of 2

asecretfile

New Member
Feb 11, 2007
228
0
0
Aug 5, 2008
#21
  • Aug 5, 2008
  • #21
joel5.0 said:
View attachment 308688... the only way I think that would be possible is, if there's a vacuum leak in the lower intake gaskets
Click to expand...

ok so upper to lower gasket wouldnt do that but lower to block gasket might?

any test I could perform to verify before tearing it down? Ive tried the carb cleaner method but its tough to get a spray on lower to head

thanks
 

Johnny P

New Member
Aug 1, 2008
5
0
0
Aug 5, 2008
#22
  • Aug 5, 2008
  • #22
I just completed a baffle swap on the lower intake (cobra) because I was getting alot of oil in the upper (3 litres after about 300 miles) my plugs were foulled and the car ran as if on 2 cylinders, the car also ran pig rich and could not hold an idle. ford racing sent out the new baffle as well as gaskets. Now I find oil consumption is not an issue but after reading this thread I checked out my oil fill nipple and there is vacuum going into the valve cover. This may be the reason I was getting so much oil before, vacuum into valve cover, excess vacuum out the pcv, enough to carry plenty of oil with it. When I completed the swap the car felt perfect all around and idled perfect. After a few days I noticed the car now struggles/hesitates to build power up to 3K rpm and hunting idle / ocassional stalling has come back. I don't think there is a leak in the lower, not after 2 installs. is this possibly the only solution / reason?
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Aug 6, 2008
#23
  • Aug 6, 2008
  • #23
well Im getting crankcase vacuum even with the manifold vacuum to pcv removed

 

Johnny P

New Member
Aug 1, 2008
5
0
0
Aug 6, 2008
#24
  • Aug 6, 2008
  • #24
new to this site, hope you don't mind me throwing in my 2 cents. I have the exact same problem and after trouble shooting and replacing parts/sensors I'm at a stand still. I think Joels right, you MAY have a vacuum leak on the lower intake to lifter vally side.
 
Prev
  • 1
  • 2
First Prev 2 of 2
You must log in or register to reply here.

Similar threads

Mustang II 4 cyl gear hunting and possibly messed up vacuum system
  • oesterreicher
  • May 31, 2026
  • 1974 - 1978 Mustang II Talk & Tech
Replies
11
Views
578
1974 - 1978 Mustang II Talk & Tech Jun 14, 2026
manicmechanic007
P
Vacuum
  • ProTechAutoServices
  • Aug 1, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
337
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 2, 2026
Noobz347
G
Idle surging after warm up
  • GALLY3309
  • Jun 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
253
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 10, 2026
Noobz347
Engine Code 41 again
  • Creomod
  • Jul 7, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
839
Fox 5.0 Mustang Tech Jul 11, 2026
Mcmahst
P
I need definitive heater valve and AC expansion valve answers
  • PurAU
  • Sep 26, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
4
Views
247
1965 - 1973 Classic Mustangs -General/Talk- Oct 1, 2026
GypsyR
G
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?