• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

valve Cover Bolt Snapped!!

  • Thread starter Thread starter 88GTStreetRod
  • Start date Start date Feb 2, 2006

88GTStreetRod

Member
Jan 5, 2004
376
1
18
USA
Feb 2, 2006
#1
  • Feb 2, 2006
  • #1
Alright, I was installing my new valve covers tonight and one of the bolts broke off. The bolt is on the bottom middle of the valve cover. If I remove the valve cover, you can get a pair of vice grips around the top section of the bot. The vice grips do nothing in trying to remove the bolt. the bolt will not budge. Any suggestions on getting this thing out?? Thanks!!!
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Feb 2, 2006
#2
  • Feb 2, 2006
  • #2
steel or aluminum heads? spray with PB blaster heat bolt up with soldier iron or torch be careful not to use too much heat as too affect head. tap with hammer and you can use a hacksaw blade and cut a groove across center and use a rachet and 1/4 in socket with a flat head screwdriver bit to remove bolt be careful not to break bolt with screwdriver bit at the cut and you may have to repeat heating,tapping and PB blaster until. removed
 
T

TheUser

Active Member
Jul 25, 2003
1,859
1
36
Springfield, MO
Feb 2, 2006
#3
  • Feb 2, 2006
  • #3
you might be able to spray some wd40 or pb blaster on it and let it set for half an hour or so. I don't think I would be applying heat to my heads.

bill: Seems like heating the bolt would make the bolt expand, which kinda is counter-productive. Heating the head might help, but might result in some head warpage. This would be my last resort.
 

5ohturbostang

New Member
Aug 30, 2004
69
0
0
cleveland
Feb 2, 2006
#4
  • Feb 2, 2006
  • #4
find out the exact bolt size,go to the hardware store and buy an extractor for that size bolt and the proper drill bit for the extractor use a punch and make a divot dead center of the break then drill into the bolt with the bit,put the extractor in the hole and make sure its straight and back it out.
 
T

TorontoJohn

New Member
Sep 8, 2004
51
1
0
Feb 2, 2006
#5
  • Feb 2, 2006
  • #5
TheUser said:
you might be able to spray some wd40 or pb blaster on it and let it set for half an hour or so. I don't think I would be applying heat to my heads.

bill: Seems like heating the bolt would make the bolt expand, which kinda is counter-productive. Heating the head might help, but might result in some head warpage. This would be my last resort.
Click to expand...


I think the expansion caused by the heat might crack the rush or whatever is holding the bolt in place.
 

iblue

New Member
Jun 27, 2005
29
0
0
Feb 3, 2006
#6
  • Feb 3, 2006
  • #6
I usually just notch the bolt with a dremel cut off wheel and back it out with a flathead screwdriver. If that dosent work for you, you can weld a nut on top of the broken bolt and back that out. That is if you have/know someone with a welder.
 

88GTStreetRod

Member
Jan 5, 2004
376
1
18
USA
Feb 3, 2006
#7
  • Feb 3, 2006
  • #7
I will try the penetrating oil and the dremel first. What is an Easy Out?
 

5ohturbostang

New Member
Aug 30, 2004
69
0
0
cleveland
Feb 3, 2006
#8
  • Feb 3, 2006
  • #8
88GTStreetRod said:
I will try the penetrating oil and the dremel first. What is an Easy Out?
Click to expand...
a easy out is an extractor its kinda like a reverse threaded drill bit but more of an aggressive thread and it is the way i would go i use them daily at work and by far the best method to do what u need to do.
 

gruvee87vertgt

20+ Year Stangneter
Oct 7, 2003
272
26
28
Chicago, Il
Feb 3, 2006
#9
  • Feb 3, 2006
  • #9
88GTStreetRod said:
I will try the penetrating oil and the dremel first. What is an Easy Out?
Click to expand...


bro, this sounds like something that will happen to me...............any luck with it?
 

ninety1gt

New Member
Aug 27, 2005
162
0
0
san antonio
Feb 3, 2006
#10
  • Feb 3, 2006
  • #10
same thing happened to me, one bolt on both heads, my dad tried tapping it but it didnt work, so he basically drilled out the bolt and put a bolt in the hole with jb weld, and used a nut to tighten it, its ghetto i know, but it worked, not leaking oil
 

88GTStreetRod

Member
Jan 5, 2004
376
1
18
USA
Feb 3, 2006
#11
  • Feb 3, 2006
  • #11
The dremel did not work, The bolt is very soft, once I had my slit cut for the srew driver, I tried unscrewing. The screw driver snapped one side of the bolt off. Now I am going to the maching shop with it. I think the bolt is cross threaded. I hand tightened the bolt, so it does not make sense, it screwed in very easy.
 

Bad92GT

The 5 Minute Plan Man
Jun 10, 2004
492
0
0
SC
Feb 3, 2006
#12
  • Feb 3, 2006
  • #12
TheUser said:
bill: Seems like heating the bolt would make the bolt expand, which kinda is counter-productive. Heating the head might help, but might result in some head warpage. This would be my last resort.
Click to expand...

you know how hot it has to get? EXTREMELY hot before it can do that.. and use a torch.. heat the bolt and the head.. principles are principles but it sure as hell works well.. i did it that way.. garuntee you the heads arent screwed..
 
8

8950HO

New Member
Mar 31, 2005
658
2
0
Feb 3, 2006
#13
  • Feb 3, 2006
  • #13
Have you guys come across this before?I can`t recall hearing a valve cover bolt breaking off.

It`s the water pump bolts/studs that like to break off and give you the headaches.

Is this a cast iron or aluminum head?
 

88GTStreetRod

Member
Jan 5, 2004
376
1
18
USA
Feb 4, 2006
#14
  • Feb 4, 2006
  • #14
iron head
 
V

v8only

Active Member
Jul 3, 2003
2,378
22
49
Feb 4, 2006
#15
  • Feb 4, 2006
  • #15
I did this once in a 66 mustang. quickly became a nightmare.

Had to drill the entire thing out. In the process, the raised area that the bolt threaded into completely collapsed, then we drilled accidently into the water jacket.

****, after that, shoved some jbweld down to plug the water jacket hole, Put the bolt where it was supposed to go, and stacked jbweld around it to make the base for the threads to go into, then shaved the excess jb off with a razor to look oem.

Car ran like that years and years and years with no issues.
 
You must log in or register to reply here.

Similar threads

D
Question about EGR valve, replacement, and a part on the valve.
  • DPP
  • May 9, 2026
  • SN95 V6 Mustang Tech
Replies
1
Views
271
SN95 V6 Mustang Tech May 23, 2026
DPP
D
A
Blow through intercooled questions
  • AngryH58
  • Aug 31, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
291
1996 - 2004 SN95 Mustang -General/Talk- Sep 1, 2026
AngryH58
A
6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Oct 19, 2026
mattcrp1
M
Drivetrain 83’ Glx convertible C5 Trans help!
  • JacksonJared2113
  • Dec 25, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
542
Fox 5.0 Mustang Tech Dec 26, 2025
JacksonJared2113
W
Speedometer and shifting issues
  • wyatt-tetro891
  • Aug 17, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
319
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 18, 2026
wyatt-tetro891
W
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?