Vibration damper questions.....

93 LX

Founding Member
Jun 2, 2000
3,081
3
0
Norwalk, CA.
This morning I started my 93 LX 5.0L stang anf lo and behold, a huge vibration. I shut her down and looked under the hood. What I saw was the weight of the Vibration damper was against the front cover and the shiney hub of the damper still attached to the crank.

My question is how do I remove the entire unit. I have a Vibration damper removal tool but if I remember correctly this attaches to the weight part of the unit. I am assuming that this will remove the weight but once removed how do I remove the hub part of the unit? Do I use a gear puller type tool? Any one run in to this issue?

HELP! LOL

Allen:eek:
 
PRO50SC said:
Yes, you need a puller.


Yes, I know but when the weight of the damper comes off how do I remove the hub of the damper. The unit it not one piece and mine has seperated. The damper removal tool screws in to the weight and assuming its still one piece the whole unit slides off the crank snout. With the unit in 2 pieces the weight will slide off but the hub will remain on the snout.

How do you remove the hub part on the snout.

Allen
 
I hate to say that I almost wonder if you would need to use a jawed puller on that. I have not done one like that so I dont know of a known easy method though.

Good luck.
 
93 LX said:
This morning I started my 93 LX 5.0L stang anf lo and behold, a huge vibration. I shut her down and looked under the hood. What I saw was the weight of the Vibration damper was against the front cover and the shiney hub of the damper still attached to the crank.

My question is how do I remove the entire unit. I have a Vibration damper removal tool but if I remember correctly this attaches to the weight part of the unit. I am assuming that this will remove the weight but once removed how do I remove the hub part of the unit? Do I use a gear puller type tool? Any one run in to this issue?

HELP! LOL

Allen:eek:


The puller should attach to the inner section of the damper. Go back and look, im pretty sure the inner hub is what is being pulled on.
 
93 LX said:
Yes, I know but when the weight of the damper comes off how do I remove the hub of the damper. The unit it not one piece and mine has seperated. The damper removal tool screws in to the weight and assuming its still one piece the whole unit slides off the crank snout. With the unit in 2 pieces the weight will slide off but the hub will remain on the snout.

How do you remove the hub part on the snout.

Allen
There arte bolt holes in the hub of the crank where the pulley bolts to. That is where you attatch the puller.

This will work but not what I'm talking about....
http://buy1.snapon.com/catalog/item...group_ID=11920&store=snapon-store&dir=catalog


This one, see the triangular shaped piece in the middle, the bolts go through there and attatch to the hub, the rest is pretty self explanitory.
http://buy1.snapon.com/catalog/item...&group_ID=1243&store=snapon-store&dir=catalog
 
87-93CrankPulley.webp


See how there are bolt holes. They bolt to the hub. (balancer) That it where the puller bolts screw to. Below


sm_igndamp.jpg



28152.JPG
 

Attachments

  • 87-93CrankPulley.webp
    87-93CrankPulley.webp
    13.5 KB · Views: 174
COOL,

I have not done it in quite some time so my memory may be a bit foggy. Maybe all the Tequila I had at my Graduation party a few weekends ago may have killed those memory cells! LOL

Anyway I need to get a new damper so I will get this done next weekend and let you know how it went!

Thanks and I hope your New Year will be safe and a good one!

Drive it like you stole it!

Allen
 
93 LX said:
COOL,

I have not done it in quite some time so my memory may be a bit foggy. Maybe all the Tequila I had at my Graduation party a few weekends ago may have killed those memory cells! LOL

Anyway I need to get a new damper so I will get this done next weekend and let you know how it went!

Thanks and I hope your New Year will be safe and a good one!

Drive it like you stole it!

Allen
NP man, good luck!!