• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Weak Starter Even When Cold

  • Thread starter Thread starter hawk232
  • Start date Start date Nov 6, 2016
  • 1
  • 2
Next
1 of 2 Next Last
H

hawk232

Member
May 2, 2006
9
1
13
Nov 6, 2016
#1
  • Nov 6, 2016
  • #1
i just picked up an 86 hatch yesterday and thought the battery was bad so i replaced it (it was old and gave me piece of mind as well) but that wasnt the issue. it has a mini starter already. the issue is that the starter engages but will not fully turn the motor over. usually after 5 or so attempts it will finally turn the motor over and start. It doesnt seem to be the solenoid since the bendix is actually engaging, its just lacking the power to actually turn over. I have a couple more grounds to clean but in the mean time i am wondering if this could be the starter going bad?
 

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,135
10,754
213
polk county florida
Nov 6, 2016
#2
  • Nov 6, 2016
  • #2
Why not replace the starter anyway? You don't know how long it's been there and if it was a weak battery it puts a strain on them. Make sure cables are the right size, clean and tight. That includes grounds, there a more than just the battery to block grounds to worry about.
Give some info on the car,
 

billison

I like tinted tail
15 Year Member
Feb 27, 2006
2,607
1,094
184
stl
Nov 6, 2016
#3
  • Nov 6, 2016
  • #3
I'd check the power wire to the starter as well
 

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,135
10,754
213
polk county florida
Nov 6, 2016
#4
  • Nov 6, 2016
  • #4
^ what he said. If you don't know the history on the car, get a repair manuel on it, not a autostore on every corner generic 79 thru 86 ford backyard book. If you are serious, look online and get a assmbly manual, or similar, most people have good intentions, still things turn into 'hack' jobs so they can get rid of a problem they didn't have the skill/patients to fix correctly.
Sorry, had too much coffee already.
 
H

hawk232

Member
May 2, 2006
9
1
13
Nov 6, 2016
#5
  • Nov 6, 2016
  • #5
i gave no info on the car because its a hodge podge job anyways lol. its an 86 4cyl car that was converted to v8. it has a mild built carb 289 in it. i just cleaned the ground on the block and both ends of the ground strap that goes from the bell housing to the firewall. problems persists.

why dont i just change the starter anyways?? throwing parts at something is usually the most expensive, least educational way of attacking a problem. the proper procedure is to diagnose the problem then replace the parts that are indicated.
 

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,135
10,754
213
polk county florida
Nov 6, 2016
#6
  • Nov 6, 2016
  • #6
hawk232 said:
i gave no info on the car because its a hodge podge job anyways lol. its an 86 4cyl car that was converted to v8. it has a mild built carb 289 in it. i just cleaned the ground on the block and both ends of the ground strap that goes from the bell housing to the firewall. problems persists.

why dont i just change the starter anyways?? throwing parts at something is usually the most expensive, least educational way of attacking a problem. the proper procedure is to diagnose the problem then replace the parts that are indicated.
Click to expand...
I really want to respond to that but I won't, I have some respect for the others on here, so go diagnose your problem, then let me know what you find.
I guess I responded anyway, oowell.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,378
18,123
224
Massachusetts
Nov 6, 2016
#7
  • Nov 6, 2016
  • #7
I assume you have tested the starter relay. Remove starter wire and have someone turn key to start. With a digital multimeter you should have continuity each and every time.

The starter circuit is simple on the pre-90 cars. One wore from solenoid to the starter, and the motor grounds on the engine.

Check to see that your engine ground is present, as without this would cause your symptoms.



If you have an engine ground present, and good wiring from battery to solenoid and solenoid to starter, then I'd go ahead and change out the starter then


Sent from my iPhone using Tapatalk
 
Reactions: General karthief, stykthyn and Davedacarpainter

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
Nov 6, 2016
#8
  • Nov 6, 2016
  • #8
Mikes right on the money.
 

Boosted92LX

It's only an inch or two. What's the big deal?
15 Year Member
Dec 19, 2010
5,721
4,244
224
Nov 6, 2016
#9
  • Nov 6, 2016
  • #9
I had a buddy that worked at Hi-Lo back before Oreilly bought them out. Back in the 80s. They had a starter testing bench with a big vise to clamp the starter in and run it. He kept a broom handle to wedge into the starter gear to see if the starter was getting weak. I watched him do it many times. He said that people made the mistake of calling the starter good if it just ran with no load.. but if it's a good starter, that sucker will make sawdust out of a broom handle. I've tried that technique many times in the garage with my vise, a set of jumper cables and a broom stick.

It'll tell you the truth in a hurry.
 
Reactions: RaggedGT

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,135
10,754
213
polk county florida
Nov 6, 2016
#10
  • Nov 6, 2016
  • #10
The truth was you just hated broom handles
 
Reactions: FoxMustangLvr

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,378
18,123
224
Massachusetts
Nov 6, 2016
#11
  • Nov 6, 2016
  • #11
Poor brooms


Sent from my iPhone using Tapatalk
 

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,135
10,754
213
polk county florida
Nov 6, 2016
#12
  • Nov 6, 2016
  • #12
I noticed you said you checked the ground from bellhousing to body. That ground need to be bolted to the head or intake, not the bellhousing. JMO
 

Boosted92LX

It's only an inch or two. What's the big deal?
15 Year Member
Dec 19, 2010
5,721
4,244
224
Nov 6, 2016
#13
  • Nov 6, 2016
  • #13
Do you want to test the starter? That's how real parts store guys did it before they had to stare at a screen drooling and ask you if you have air conditioning...
 
Reactions: 02 281 GT and General karthief
H

hawk232

Member
May 2, 2006
9
1
13
Nov 6, 2016
#14
  • Nov 6, 2016
  • #14
i have not tested continuity on the relay but assumed since the starter is engaging (just lacks the power to spin the motor) that the relay was fine. is it possible for the relay to activate but somehow have enough resistance to not allow enough power through?

I have cleaned all of the grounds (I will check on moving the body ground to the head/intake) all that is left are the power wires on the starter itself. When the parts store tests them, can they check to see how they perform under load or do they simply say "passed" if it spins?

Mike, thanks for the schematic! The "engine ground" that you refer to, are you talking about from the battery to the block? I have that, it seems to be a newer cable and is in good condition (just sanded/cleaned all terminals this morning). I do not seem to have a block to frame ground (just the bellhousing to firewall)...
 

Boosted92LX

It's only an inch or two. What's the big deal?
15 Year Member
Dec 19, 2010
5,721
4,244
224
Nov 6, 2016
#15
  • Nov 6, 2016
  • #15
hawk232 said:
I have cleaned all of the grounds (I will check on moving the body ground to the head/intake) all that is left are the power wires on the starter itself. When the parts store tests them, can they check to see how they perform under load or do they simply say "passed" if it spins?
Click to expand...

That's the point I was trying to make. Most of the idiots now a days won't or can't load test it. If you have a vise, some jumper cables and a board or broom stick you can do it yourself and let the dummies at the parts store ask dumb questions.
 
Reactions: General karthief

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,378
18,123
224
Massachusetts
Nov 6, 2016
#16
  • Nov 6, 2016
  • #16
There is the neg terminal of the battery that connects to the block, and another ground that runs from head to firewall. It may also connect to a bellhousing bolt as the bolt passes into the block.

Barring any loose connection, if that's all intact then the starter should crank.

If starter engages each time, then solenoid is prob ok.

After checking the wiring, I'd prob test/replace the starter at that point.


Sent from my iPhone using Tapatalk
 
H

hawk232

Member
May 2, 2006
9
1
13
Nov 6, 2016
#17
  • Nov 6, 2016
  • #17
LOL

well i think my wife found the problem... i asked her to come try to start it while i check batt voltage. started like 10 times in a row, i tried and got the same results i always do. turns out that if the key is turned ALL the way, power stops being sent, if turned only partially, it cranks everytime! I will try that for a bit and see if thats all it is.
 
Reactions: Mustang5L5
H

hawk232

Member
May 2, 2006
9
1
13
Nov 6, 2016
#18
  • Nov 6, 2016
  • #18
now i am moving on to figure out why my pass window doesnt work. got the door panel off and the motor is turning but nothing is happening. havent seen one of these assemblies out of the car so i dont know how they work. let the research begin!
 

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,135
10,754
213
polk county florida
Nov 6, 2016
#19
  • Nov 6, 2016
  • #19
hawk232 said:
now i am moving on to figure out why my pass window doesnt work. got the door panel off and the motor is turning but nothing is happening. havent seen one of these assemblies out of the car so i dont know how they work. let the research begin!
Click to expand...
Plasic pucks inside the drive mechanism, you can get'em at the zone, remove motor and then two more little bolts and the cover over the gear then you'll see the crud that used to be little round pucks, clean it, replace the pucks with some grease, grease up the window tracks while your there and you'll be good to go.
 
Reactions: Boosted92LX
H

hawk232

Member
May 2, 2006
9
1
13
Nov 6, 2016
#20
  • Nov 6, 2016
  • #20
dang, i should have checked back sooner! i pulled the motor and found the pucks, assumed that they were stripped pieces of gear and threw them in the garbage! the pucks themselves are available at the zone? i assumed i needed a new motor...
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

M
85 mustang 5.0 cranking in run position
  • Mamaclean
  • May 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
265
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 1, 2026
General karthief
M
Bad starter?
  • mason5.0
  • Oct 6, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
254
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 6, 2026
General karthief
Fox won't crank over and fuel pump won't kick on.
  • djj62478
  • Jun 7, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
679
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 11, 2026
General karthief
Hard to start when engine is cold
  • 86_Capri
  • Mar 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
32
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
E
2007 GT Stalls when lights or a/c turned on
  • ejscarfo
  • Jun 22, 2026
  • 2005 - 2009 Specific Tech
Replies
3
Views
371
2005 - 2009 Specific Tech Sep 26, 2026
manicmechanic007
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?