• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Weird Vacuum

  • Thread starter Thread starter jh73
  • Start date Start date Oct 29, 2005
  • 1
  • 2
Next
1 of 2 Next Last

jh73

New Member
Apr 27, 2005
28
0
0
Memphis, TN
Oct 29, 2005
#1
  • Oct 29, 2005
  • #1
I did a vacuum test on my car today and the needle bounced very rapidly between 15 and 20 at idle (750 to 800 rpm). What does this mean???
 

jh73

New Member
Apr 27, 2005
28
0
0
Memphis, TN
Oct 29, 2005
#2
  • Oct 29, 2005
  • #2
anyone
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Oct 29, 2005
#3
  • Oct 29, 2005
  • #3
Was your idle fluctuating between 750 and 800 RPM? That could just be caused by the change in engine speed, and possibly a little leak somewhere.
 

90mustangGT

I felt sorry for girls because
Founding Member
Jan 15, 2002
2,773
17
89
Dallas, GA
Oct 30, 2005
#4
  • Oct 30, 2005
  • #4
It could mean many things. Fluxuating vaccume can indicate a vaccume leak on a few cylinders (such as the upper/lower intake), poor compression, valve sealing issues, collapsed lifter, as well as clogged exaust. It's just something that takes more time to find.
 

jh73

New Member
Apr 27, 2005
28
0
0
Memphis, TN
Oct 30, 2005
#5
  • Oct 30, 2005
  • #5
90mustangGT said:
It could mean many things. Fluxuating vaccume can indicate a vaccume leak on a few cylinders (such as the upper/lower intake), poor compression, valve sealing issues, collapsed lifter, as well as clogged exaust. It's just something that takes more time to find.
Click to expand...
Where would be the best place to start checking?
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Oct 30, 2005
#6
  • Oct 30, 2005
  • #6
I would start with looking for a vac leak, then a compression check and a cyl. leakdown test.
Look for a vac leak using starting fluid. With the motor idling, spray a cautious amount near the suspected vac leak, if the rpms jump up then you know the starting fluid was pulled into the intake charge via a vac leak.
 

jh73

New Member
Apr 27, 2005
28
0
0
Memphis, TN
Oct 30, 2005
#7
  • Oct 30, 2005
  • #7
vristang said:
I would start with looking for a vac leak, then a compression check and a cyl. leakdown test.
Look for a vac leak using starting fluid. With the motor idling, spray a cautious amount near the suspected vac leak, if the rpms jump up then you know the starting fluid was pulled into the intake charge via a vac leak.
Click to expand...
I have already done that. I have been looking for the leak for sometime now and can not find it. What is the correct amount of compression should I have?
 

ram360

Founding Member
Oct 19, 2002
2,162
1
59
Pennsylvania
Oct 30, 2005
#8
  • Oct 30, 2005
  • #8
I wouldn't be worried 15-20 lbhg vacuum is good and normal. I wouldn't start looking for problems.
 

jh73

New Member
Apr 27, 2005
28
0
0
Memphis, TN
Oct 30, 2005
#9
  • Oct 30, 2005
  • #9
ram360 said:
I wouldn't be worried 15-20 lbhg vacuum is good and normal. I wouldn't start looking for problems.
Click to expand...
What led me to start looking for a vacuum leak is that my car idles like crap almost as if it had a cam in it (I wish). It is also running very rich, burning the hell out of gas and when I rev up the motor the idle revs up fine but when it is coming back down it will stick at 1500 rpm for about 2 or 3 seconds and then slowly come back down to idle. I have already changed the IAC, TPS(98 volts), MAF, ACT, spark plugs & wires, Cap and Rotor, replaced 3 vacuum lines and tore apart my TB and EGR plate and cleaned it. At this point I am about to go crazy!
 

Look Its Aaron

Your car looks like it came straight from Mexico.
Founding Member
Nov 18, 2001
2,634
0
48
Fontana, Cali
Oct 30, 2005
#10
  • Oct 30, 2005
  • #10
did you dump the codes?
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Oct 30, 2005
#11
  • Oct 30, 2005
  • #11
jh73 said:
I have already done that. I have been looking for the leak for sometime now and can not find it. What is the correct amount of compression should I have?
Click to expand...

I am not sure what the compression numbers should be, but most will agree that they should be within 10% of the highest cyl. Leakdown numbers should indicate 10% leakdown or less. Maybe a little more with increased engine wear. Over 15% is probably cause for concern.
Most compression gauges/leakdown gauges/vac gauges will have a guide card with them. This will help to interpret what the results mean. I can't find any of mine right now, or I would just post it up.
Maybe someone else can find theirs?
 

jh73

New Member
Apr 27, 2005
28
0
0
Memphis, TN
Oct 30, 2005
#12
  • Oct 30, 2005
  • #12
Look Its Aaron said:
did you dump the codes?
Click to expand...
67 and 111 which does not pertain to my problems.
 

CManT1914

New Member
Feb 5, 2004
3,172
2
0
Killeen, Texas
Oct 30, 2005
#13
  • Oct 30, 2005
  • #13
jh73 said:
I have already done that. I have been looking for the leak for sometime now and can not find it. What is the correct amount of compression should I have?
Click to expand...

Probably around 150 or so. But you're really looking for no more than 10% difference between cylinders.
 

90mustangGT

I felt sorry for girls because
Founding Member
Jan 15, 2002
2,773
17
89
Dallas, GA
Oct 31, 2005
#14
  • Oct 31, 2005
  • #14
A leakdown test I belive would tell you best what's going on. Somehow one or more cylinders just isn't pulling as much as the others. Does your car a catted mid-pipe? The firing order of the engine makes for two pulses on each bank before going to the oppisite side of the engine, so if one side were clogged, there would be a restriction. If you had a collapsed lifter, on the exaust side the gasses wouldn't be able to escape, and it would back into the intake when it opens. Intake collapsed then of course it wouldn't open enough to pull the air in. If your checked for vacuum leaks, andyour car still has converters, I would look into this first. Check the temp in the front, then in the rear of the converter, the temp in the exit of the converter should be hotter than the inlet, if the temp in the inlet is considerably hotter, then you have a restriction. If it's about the same, then that just means the converter isnt' working. I'd really love to help but it's hard over the net.
 

jh73

New Member
Apr 27, 2005
28
0
0
Memphis, TN
Oct 31, 2005
#15
  • Oct 31, 2005
  • #15
90mustangGT said:
A leakdown test I belive would tell you best what's going on. Somehow one or more cylinders just isn't pulling as much as the others. Does your car a catted mid-pipe? The firing order of the engine makes for two pulses on each bank before going to the oppisite side of the engine, so if one side were clogged, there would be a restriction. If you had a collapsed lifter, on the exaust side the gasses wouldn't be able to escape, and it would back into the intake when it opens. Intake collapsed then of course it wouldn't open enough to pull the air in. If your checked for vacuum leaks, andyour car still has converters, I would look into this first. Check the temp in the front, then in the rear of the converter, the temp in the exit of the converter should be hotter than the inlet, if the temp in the inlet is considerably hotter, then you have a restriction. If it's about the same, then that just means the converter isnt' working. I'd really love to help but it's hard over the net.
Click to expand...
Thanks for the reply 90mustangGT! And no I do not have converters on the car. I wish I could find someone around where I live That knew what they were talking about. Everytime I take it somewhere thay all tell me something different, I even to took it to a Ford dealership and they couldn't tell me squat. I am tired of sinking money into it and getting anywhere. I will try the leakdown test and see where that takes me. Thanks!
 

ram360

Founding Member
Oct 19, 2002
2,162
1
59
Pennsylvania
Oct 31, 2005
#16
  • Oct 31, 2005
  • #16
jh73 said:
What led me to start looking for a vacuum leak is that my car idles like crap almost as if it had a cam in it (I wish). It is also running very rich, burning the hell out of gas and when I rev up the motor the idle revs up fine but when it is coming back down it will stick at 1500 rpm for about 2 or 3 seconds and then slowly come back down to idle. I have already changed the IAC, TPS(98 volts), MAF, ACT, spark plugs & wires, Cap and Rotor, replaced 3 vacuum lines and tore apart my TB and EGR plate and cleaned it. At this point I am about to go crazy!
Click to expand...

Maybe it's just me but I don't think it's a vacuum leaking causing the idle fluctuation. I mean that's a good solid vacuum it's pulling. Awhile back vristang was helping me w/ a vacuum problem on my car. In my case I was only pulling like 3hg at idle. I couldn't find a leak anywhere. Turned out when I hooked my egr back up I pulled a direct vacuum to it from the intake. This caused the egr to be open all the time causing an enoumous vacuum leak that I couldn't find (should have been running to the solenoid first)
 

jh73

New Member
Apr 27, 2005
28
0
0
Memphis, TN
Oct 31, 2005
#17
  • Oct 31, 2005
  • #17
ram360 said:
Maybe it's just me but I don't think it's a vacuum leaking causing the idle fluctuation. I mean that's a good solid vacuum it's pulling. Awhile back vristang was helping me w/ a vacuum problem on my car. In my case I was only pulling like 3hg at idle. I couldn't find a leak anywhere. Turned out when I hooked my egr back up I pulled a direct vacuum to it from the intake. This caused the egr to be open all the time causing an enoumous vacuum leak that I couldn't find (should have been running to the solenoid first)
Click to expand...
But shouldn't the needle be stationary on the vacuum tester? Mine is almost like a blur between 15 and 20.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Oct 31, 2005
#18
  • Oct 31, 2005
  • #18
If the motor is healthy, and all is well your vac signal should be steady within about +/- 1".

I want to say that having a vac signal jump around at idle is an indication of the valves not sealing properly, but that is from memory and I don't trust my memory these days. I think this could cause vac fluctuations by allowing for revesion in the intake during compression/exhaust strokes.
Like I said though, that is from memory.

As an aside, remember that vac leaks do not only occur externally. Ram360 gives a good example. Also, I had a lower intake gasket slip down during assembly, which allowed for a vac leak common to the lifter valley. I had a very good vac signal, even before replacing the gasket. Only reason I found it was because I put the vac gauge on the outlet of the pcv. The moral of the story is that sometimes the starting fluid method of tracking down a vac leak is pretty useless.

ram360;
I had forgotten all about your vac problems. Glad to hear you got it sorted out
 

jh73

New Member
Apr 27, 2005
28
0
0
Memphis, TN
Oct 31, 2005
#19
  • Oct 31, 2005
  • #19
vristang said:
If the motor is healthy, and all is well your vac signal should be steady within about +/- 1".

I want to say that having a vac signal jump around at idle is an indication of the valves not sealing properly, but that is from memory and I don't trust my memory these days. I think this could cause vac fluctuations by allowing for revesion in the intake during compression/exhaust strokes.
Like I said though, that is from memory.

As an aside, remember that vac leaks do not only occur externally. Ram360 gives a good example. Also, I had a lower intake gasket slip down during assembly, which allowed for a vac leak common to the lifter valley. I had a very good vac signal, even before replacing the gasket. Only reason I found it was because I put the vac gauge on the outlet of the pcv. The moral of the story is that sometimes the starting fluid method of tracking down a vac leak is pretty useless.

ram360;
I had forgotten all about your vac problems. Glad to hear you got it sorted out
Click to expand...
What is the best way to check the valves outside of tearing the heads off? I heard it could also be caused by and ignition problem. Is this true? And thinks for the all the input!
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Oct 31, 2005
#20
  • Oct 31, 2005
  • #20
The only other way I can think of right now, is with a compression check. If a valve is not seating properly it should show on a compression test.
A Leakdown test would work too.
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

L
Engine 85 GT Excessive Idle
  • lutzkecj
  • Sep 18, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
369
Fox 5.0 Mustang Tech Sep 21, 2026
86HO5.0
8
8
Foxbody high rpms and surging rpms
  • 86foxseth
  • Jun 9, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
354
Fox 5.0 Mustang Tech Jun 13, 2026
Noobz347
Mustang II 4 cyl gear hunting and possibly messed up vacuum system
  • oesterreicher
  • May 31, 2026
  • 1974 - 1978 Mustang II Talk & Tech
Replies
11
Views
581
1974 - 1978 Mustang II Talk & Tech Jun 14, 2026
manicmechanic007
K
Resolved Need some assistance. Holley Terminator X alongside H/C/I. Very rough/inconsistent idle
  • karhoot
  • Jun 6, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
236
Fox 5.0 Mustang Tech Jun 6, 2026
karhoot
K
A
SN95 Multifunction Madness! Need some big brain assistance from you folks
  • Awnaw
  • Oct 28, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
135
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 10, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?