Where can I get OEM rubber exhaust hangers??

Mustang5L5 · Jul 11, 2009

I need 3.

Right now i have aftermarket hangers on my car and they are just too flimsy. It allows my exhaust to move too much and it bangs on the framerail in the rear when i bog the engine down.

The Ford ones are MUCH stiffer and will keep it more solid.

I really don't want to spend $14 each for 3 of them.

79-98 HANGER, MUFFLER, UPPER, LH MUSTANG

Does anyone have a different source?

1991notchbackLX · Jul 11, 2009

CJ Pony Parts

Muffler Hangers Ford OEM

86-98 LH Upper each $14.95 E6ZZ5260A
86-98 RH Upper each $23.95 E6ZZ5C263A
87-93 RH Lower each $28.95 E8ZZ5A294A

Tail Pipe Hangers Ford OEM

90-97 V8/94-97 V6 each $20.95 F4ZZ5256A

Exhaust Hanger Insulator

87-93 5.0L each $4.95 EXHI1

I hope that helps. It looks like they're relatively expensive no matter which ones you buy. I'm sure a dealership would hit you even harder for them though.

Mustang5L5 · Jul 12, 2009

Damn that's crazy.

I'm gonna hit the parts store up and see what I can figure out. I just need to restrict movement, so i'm sure i can come up with something.

bada$$92 · Jul 13, 2009

I might have some in my tool box , I'll give you a call later when i get to work.

Mustang5L5 · Jul 13, 2009

bada$$92 said:
I might have some in my tool box , I'll give you a call later when i get to work.

Cool thx.

Leave me a message if it goes to VM. I get no service in my building because it's shielded

Darkwriter77 · Jul 13, 2009

The ones I've bought before at Autozone are pretty close to the same as stock, and they're pretty darned stiff. I've always had to slather them up with silicone to get the hanger to actually poke in there. Also, they don't always have the hole going all the way through the middle, so you'll have to poke a flathead screwdriver or something to de-virginize it so the hanger then can poke through, and it's a snug fit, hence the lube. (Wow, this is just starting to sound all kinds of perverted... )

Beasty306GT · Jul 13, 2009

autozone is ur best bet

LiquidGT · Jul 13, 2009

I had problems with my tail knocking the frame when the car was at a standstill, so I got one of those tailpipe hanger kits from AZ. I only used the rubber strap that came in the box and I wrapped it around the part of the tail that was hitting the frame.... it hasn't knocked in years. I know its not the classiest idea, but no one sees the bottom of my car anyway.

Mustang5L5 · Jul 13, 2009

LiquidGT said:
I had problems with my tail knocking the frame when the car was at a standstill, so I got one of those tailpipe hanger kits from AZ. I only used the rubber strap that came in the box and I wrapped it around the part of the tail that was hitting the frame.... it hasn't knocked in years. I know its not the classiest idea, but no one sees the bottom of my car anyway.

That's what I did!!! I put a rubber bumper on the tailpipe!!

Actually, i found a corner of the pipe that was hitting the gas tank that I never saw. I adjusted the cat-back so it should be good now.

I still want to put the OEM hangers on as at idle my tips move around a bit. My buddy has some stuff ford rubbers he's gonna hook me up with

Where can I get OEM rubber exhaust hangers??

Mustang5L5

That is…until I whipped out my Bissell

1991notchbackLX

Active Member

Mustang5L5

That is…until I whipped out my Bissell

bada$$92

New Member

Mustang5L5

That is…until I whipped out my Bissell

Darkwriter77

Resident Ranting Negative Nancy

Beasty306GT

Active Member

LiquidGT

Member

Mustang5L5

That is…until I whipped out my Bissell

Similar threads

Where can I get OEM rubber exhaust hangers??

That is…until I whipped out my Bissell

Active Member

That is…until I whipped out my Bissell

New Member

That is…until I whipped out my Bissell

Resident Ranting Negative Nancy

Active Member

Member

That is…until I whipped out my Bissell

Similar threads

Privacy & Transparency

Privacy & Transparency