• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Where Should I Drill?

  • Thread starter Thread starter bretamo
  • Start date Start date Jul 29, 2007

bretamo

Member
May 13, 2005
122
1
16
Jul 29, 2007
#1
  • Jul 29, 2007
  • #1
I am writing for suggestions on where to drill in order to route a positive wire so I can power the lights for my 3 gauges mounted on the outside of the car on the cowl grill.

My goal is to use the interior's dimmer switch so the lights on the gauges match those inside the car. But where is the best place to drill in-and-around the cowl grill area?

Do I drill from the grill area through to the interior and hope I don't hit anything? Or do I go out side the cowl area into the engine bay and back into the interior of the car through the steering column boot?

Do I drill from inside the car into the cowl grill area, and if so, where is the best place for this?

So far I've hooked up the mechanical vacuum gauge and fuel pressure gauges and am happy to report about 18lbs of vac and 38lbs of fuel pressure. But that's in the daylight, so I need your suggestions to know if is the same after dark

Thanks in advance.
 

powertrax91

Founding Member
Mar 13, 2002
598
0
17
New York
Jul 30, 2007
#2
  • Jul 30, 2007
  • #2
no need to drill... feed the wires through the same hole as the speedo cable
 

wythors

Get off my lawn!!!
Founding Member
May 17, 2000
2,277
35
69
C Addle
Jul 30, 2007
#3
  • Jul 30, 2007
  • #3
powertrax91 said:
no need to drill... feed the wires through the same hole as the speedo cable
Click to expand...


Or the hood release cable, which will put your wire in the general area where the bundle of wires comes out from underneath the dash. Check your wiring diagram for the color of the power wire for the dash lights and find it in that bundle. That's where I tapped it for my gauges and everything works great.
 

bretamo

Member
May 13, 2005
122
1
16
Jul 30, 2007
#4
  • Jul 30, 2007
  • #4
The hood release and speedo cable do not enter into the interior through the cowl grill area, do they?

I want to go directly through the cowl grill bay into the interior if I can.
 

powertrax91

Founding Member
Mar 13, 2002
598
0
17
New York
Jul 30, 2007
#5
  • Jul 30, 2007
  • #5
no they don't, but you can drill a small hole behind the MAP sensor
 
You must log in or register to reply here.

Similar threads

C
Electrical Fuel Gauge...Help! What did I do or Didn't Do?
  • ChickenDeluxe
  • Sep 3, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
250
Fox 5.0 Mustang Tech Sep 3, 2026
ChickenDeluxe
C
D
2006 GT Windshield Cowl install
  • Daddidio
  • Mar 12, 2026
  • 2005 - 2009 Specific Tech
Replies
0
Views
292
2005 - 2009 Specific Tech Mar 12, 2026
Daddidio
D
M
1996 GT Speedometer electrical nightmare
  • moon96gt
  • Oct 7, 2026
  • SN95 4.6L Mustang Tech
Replies
2
Views
195
SN95 4.6L Mustang Tech Oct 17, 2026
CAMTWO1070
T
Progress Thread 2002 Mustang 3.8L CV
  • TheIncompetentMechanic
  • May 26, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
168
1996 - 2004 SN95 Mustang -General/Talk- Jun 1, 2026
TheIncompetentMechanic
T
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
491
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?