• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

will these valve covers fit

  • Thread starter Thread starter ronstang94
  • Start date Start date Oct 4, 2007

ronstang94

Member
May 10, 2007
204
1
18
Phx, AZ
Oct 4, 2007
#1
  • Oct 4, 2007
  • #1
ive been looking at some ford racing valve covers, either these http://www.blueovalindustries.com/products.php?pid=99011898 or http://www.blueovalindustries.com/products.php?pid=99011906. will these fit under the stock intake and will there be a problem with the alternater clearance (heard someone say there would be a problem)? would they fit under the edelbrock performer intake? do I maybe need an intake spacer to make it work? and if so will all of this fit under my 96-98 cobra hood? Thanks
 

diablostang

New Member
Sep 21, 2004
425
0
0
Raleigh, NC
Oct 5, 2007
#2
  • Oct 5, 2007
  • #2
These are a bit cheaper-

http://cgi.ebay.com/ebaymotors/ws/e...m=330171963870&ssPageName=STRK:MESE:IT&ih=014

And from what I know, they generally fit with a 1/2" spacer.. others can chime in to confirm though. When I ran those, I was carbed so I didn't have to worry. My buddy with his EFI fox ran them with a 1/2" spacer and an Edelbrock RPM II, and stock hood.

I would NOT buy the first set you posted though... They're stamped steel (very thin) so they tend to bend when you tighten them, causing leaks. Also, the baffle has to be cut out to fit roller rockers under them.
 

Yellow302

Member
Mar 2, 2003
789
2
19
NJ
Oct 5, 2007
#3
  • Oct 5, 2007
  • #3
second ones wont, needed a 1 inch spacer for my intake, if you run the elbow on the stock intake it may never fit. You may need an after market hood if you raise it up too.
 

final5-0

Mustang Master
Apr 6, 2003
6,817
12
79
DFW Texas
Oct 5, 2007
#4
  • Oct 5, 2007
  • #4
I can say for certain there is more room under the Edel intakes than on
the Cobra and TFS intakes

Myself and several other folks I know have ran the Edels with NO spacer.

I used Fox vc's and Scorpion stud mount rr's with AFR heads

I did have to do a few mods to make the Fox vc's work

I don't know if those vc's you linked would work

Grady
 
You must log in or register to reply here.

Similar threads

Mustang II 4 cyl gear hunting and possibly messed up vacuum system
  • oesterreicher
  • May 31, 2026
  • 1974 - 1978 Mustang II Talk & Tech
Replies
11
Views
577
1974 - 1978 Mustang II Talk & Tech Jun 14, 2026
manicmechanic007
6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Oct 19, 2026
mattcrp1
M
Exhaust 1 3/4” Long Tubes on a Fox Body AOD – Easiest route?
  • 5.0 Mike
  • Mar 19, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
2K
Fox 5.0 Mustang Tech Mar 21, 2025
5.0 Mike
M
Resolved PCV Tube and Valve Cover Breather Hole Locations
  • MDrisc
  • Sep 11, 2024
  • Fox 5.0 Mustang Tech
Replies
3
Views
1K
Fox 5.0 Mustang Tech Sep 22, 2024
MDrisc
M
94-95 Cobra Intake
  • Va89Stang
  • Jul 15, 2024
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
960
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 29, 2024
rednotch
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?