• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Wiper Problems

  • Thread starter Thread starter ImportSlayer347
  • Start date Start date Oct 15, 2008

ImportSlayer347

Member
Oct 13, 2008
173
1
19
Sarasota, FL
Oct 15, 2008
#1
  • Oct 15, 2008
  • #1
I was driving today with no troubles and it started to sprinkle a little. I turned the wipers on and no matter what setting I put it on, I only got one speed. I switched it off and they kept going at that one slow delayed speed. I cannot get them to shut off now.

Another thing. If I unhook the harness on the switch on the column, it doesn't change. It keeps going on that delay. If I unhook the harness right on the wiper motor that goes to the switch, it runs at full speed. Does this mean there is a problem in the wire harness going to the switch or a problem with the motor?

Where can I get a wiring diagram for the wiper motor?
 

Saleen0679

10 Year Member
Apr 14, 2005
876
24
49
Yakima, WA
Oct 15, 2008
#2
  • Oct 15, 2008
  • #2
Possible Interval Governor problem.



Governor looks like



and is located near the steering column under the dash.
 

Attachments

  • 92wiperjf3.webp
    15.6 KB · Views: 393
  • wipergovsw2038ut4.th.webp
    8.6 KB · Views: 280

ImportSlayer347

Member
Oct 13, 2008
173
1
19
Sarasota, FL
Oct 16, 2008
#3
  • Oct 16, 2008
  • #3
Can this be bypassed or does it have to be replaced? Where can I buy one?
 

ImportSlayer347

Member
Oct 13, 2008
173
1
19
Sarasota, FL
Oct 16, 2008
#4
  • Oct 16, 2008
  • #4
I have the whole underside of the dash and column taken apart. I cannot physically locate it. Is it attached to the multi function switch?

I got a part number from Ford and found a few places online that sell it. I gotta find it first though.
 

ImportSlayer347

Member
Oct 13, 2008
173
1
19
Sarasota, FL
Oct 16, 2008
#5
  • Oct 16, 2008
  • #5
The wires go straight from the Multifunction switch into the wiring harness. I am really confused now.
 

Saleen0679

10 Year Member
Apr 14, 2005
876
24
49
Yakima, WA
Oct 16, 2008
#6
  • Oct 16, 2008
  • #6
It's fairly out in the open. You should be able to just look up under the dash. It's inline with the clutch pedal. The clutch pedal pad almost points to it.
 

ImportSlayer347

Member
Oct 13, 2008
173
1
19
Sarasota, FL
Oct 17, 2008
#7
  • Oct 17, 2008
  • #7
Is it possible this delay module has been deleted? The washer motor has been deleted I know for sure. I only ask because I think I found were it is supposed to be. There are two screws there, but whatever they were holding in place is now gone. I wonder if the guy before me that did the wiring circumvented the governor to remove it.
 

Saleen0679

10 Year Member
Apr 14, 2005
876
24
49
Yakima, WA
Oct 17, 2008
#8
  • Oct 17, 2008
  • #8
Anything is possible especially if you're not the original owner. Who knows what's been done to the car. Here's a breakdown of where the governor would be mounted. Chances are yours has been removed and the system rewired. If so, you're going to have to trace wires, check connections and compare them to the schematic. It would narrow your problem down to the motor, wiring, and switch.

 

Attachments

  • governorlocationmc6.webp
    46.2 KB · Views: 749

ImportSlayer347

Member
Oct 13, 2008
173
1
19
Sarasota, FL
Oct 17, 2008
#9
  • Oct 17, 2008
  • #9
Yep it has definitely been removed. That was the spot I was looking at. I pulled the switch completely out. After I pulled all the harnesses off, the wipers stopped. Stupid MF switch is probably bad.

Thanks for that pic of the module location. You da man.

How can I test the switch with a meter?
 

Saleen0679

10 Year Member
Apr 14, 2005
876
24
49
Yakima, WA
Oct 17, 2008
#10
  • Oct 17, 2008
  • #10

 

Attachments

  • mftesting1.webp
    29.8 KB · Views: 260
  • mftesting2.webp
    57.3 KB · Views: 199

ImportSlayer347

Member
Oct 13, 2008
173
1
19
Sarasota, FL
Oct 17, 2008
#11
  • Oct 17, 2008
  • #11
I checked the part number on this switch that I pulled and it was f2zc-13k359-aa. Correct me if I am wrong, but isn't that for a 94+, not a 87-93? I think that explains how he was able to delete the module.
 

Saleen0679

10 Year Member
Apr 14, 2005
876
24
49
Yakima, WA
Oct 17, 2008
#12
  • Oct 17, 2008
  • #12
That's the correct P/N for a 90-93 MF switch. The 94 still has some type of wiper control module between the MF switch and the motor, but I don't know if it's even possible to just R&R the switch with a pre-93 vehicle.
 

ImportSlayer347

Member
Oct 13, 2008
173
1
19
Sarasota, FL
Oct 18, 2008
#13
  • Oct 18, 2008
  • #13
I tested the switch per your instructions...BAD!!

Gas for trip to junkyard - $5
Junkyard purchase - $40
Having wipers in the rain - priceless

Once again Saleen, you da man!!

Where you get all those schematics?

:SNSign:
 

Saleen0679

10 Year Member
Apr 14, 2005
876
24
49
Yakima, WA
Oct 18, 2008
#14
  • Oct 18, 2008
  • #14
Gotta love easy fixes. Most of the diagrams come from the Mustang EVTM (Electrical & Vacuum Troubleshooting Manual). Ford put one out for each year of vehicle. They are invaluable. Get one.
 
You must log in or register to reply here.

Similar threads

J
Wipers won't work at all
  • jpfox
  • May 8, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
684
Fox 5.0 Mustang Tech May 16, 2025
nickyb
D
Electrical Weird door wiring issues
  • Dakar09
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
203
Fox 5.0 Mustang Tech Oct 21, 2026
Dakar09
D
A
Electrical electric mirror switch issue...
  • alchemist1
  • Apr 18, 2026
  • Fox 5.0 Mustang Tech
Replies
1
Views
188
Fox 5.0 Mustang Tech Apr 19, 2026
2000xp8
C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
381
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
A
Resolved Windshield wiper troubleshooting - Wiper turns OFF when Headlights turned ON
  • afjLX
  • Feb 9, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
897
Fox 5.0 Mustang Tech Mar 30, 2025
General karthief
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?