Navigation
Trending media
-
-
Media 'Mustang Throwout Bearing & Clutch Fork Install (79-04)' in category 'Mustang Technical Videos'- Jarrod@latemodel
Comments: 0 -
-
-
Imported Item
-
Kensgt - Jun 26, 2009
- 0 Comments
Guy primers the car but doesn't do ANY bodywork and doesn't even get the rust off like here..
Imported Item
-
Kensgt
- Jun 26, 2009
- 0 Comments
....now look at the ride height for the rear. Not sure what the guy did to the springs when he replaced the shocks but chit, looks bad. Oh well i'm gonna swap them out for some Eibachs anyway.
Imported Item
-
Kensgt
- Jun 26, 2009
- 0 Comments
ok, here is the front tires, notice the ride height.....
Imported Item
-
Kensgt
- Jun 26, 2009
- 0 Comments
I know, looks rough but runs well. Guy that owned it before primered the whole car and didn't mask the engine, after removing the primer I noticed that the paint is almost gone in a lot of places....ugggg I hate messy engine compartments.
Imported Item
-
Kensgt
- Jun 26, 2009
- 0 Comments
Imported Item
-
Kensgt
- Jun 26, 2009
- 0 Comments
This is after I replaced the gangsta lean seats with some used ones from a 94 GT.
Imported Item
-
Kensgt
- Jun 26, 2009
- 0 Comments
Since this I have replaced the guage cluster lens, rearview mirror and added a steeda shifter
Imported Item
-
Kensgt
- Jun 26, 2009
- 0 Comments
this sucks, body is excellent except for this, messed up the hatch too. New bumper plus quarter panel plus labor=BROKE!
m 9ee4551630344a6d96b9178810d1b87a
m 5d00905ee9d94042a793c80ee9870ca8
Imported Item
-
5.0Torx - Jun 25, 2009
- 0 Comments
IMG 3414 2
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 2778 2
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 2765 2
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 2760 2
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 3064 2
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 3044 2
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 3035 2
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 3013 2 - this is the #2 cylinder. i left #1 out because it is completely unaffected by non-P headers
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 3012 2 - this is the #3 cylinder
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 3011 2 - this is the #4 cylinder
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 3010 2 - this is the passengers cylinder head overview shot
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 3002 2 - this is the #8 cylinder
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 3001 2 - this is the #7 cylinder, easily the tightest squeeze with non-P headers
Imported Item
-
5.0Torx
- Jun 25, 2009
- 0 Comments
IMG 3000 2 - this is the #6 cylinder