Search results

  1. 6

    Where is it coming from?

    I am going crazy. My 96 Cobra has a burning electrical smell coming from the drivers side of the motor - somewhere between the firewall and 18 inches forward of the firewall. I have put it up in the air and looked all over but the strong smell continues whenever the motor is running. I pulled...
  2. 6

    Door rattle is getting to me

    The passenger door has an irritating rattle coming from inside the rear of the door below the lock knob. Any tricks I should know so I don't damage the trim/door panel when I remove it to see what is going on? Any common areas of noise there so I can have parts ready to go? Thanks.
  3. 6

    Kudos to CJ Pony Parts

    It is not often that I am impressed by a vendor, but CJ Pony Parts worked hard to satisfy my needs. The seat upholstery kit arrived without the headrest covers and CJ immediately resolved the issue and had the third party manufacturer drop ship the covers to me. They arrived as promised. Well...
  4. 6

    Beware Ford Extended Warranty (ESP) SVT Motor

    Ford is refusing the transfer an extended warranty to me (per the contract terms Section 11A) for my Ford Factory crate 4.6 32V. They will not explain why and have decided to break the contract. I assume this is because a large Corporation can ignore one person, and their new internal policy...
  5. 6

    Ideal 302 Roller Block Year?

    Please correct me if I'm wrong. I think that the 89 5.0 roller may be an excellent platform because it has the roller cam, forged pistons, and basic EFI. Is there a better year block/engine to start a 302 or 331 build?
  6. 6

    Do you have Flo Fits? 2 Questions

    I am considering putting a used set of Flo Fits in my 68 vert. Do they sit higher and, if so, how much? Do they adjust further back? The problem is that with the stock seats, my knees hit the steering wheel a little. If the Flo Fits sit higher, that might be a problem. Thanks.
  7. 6

    Roller Rockers: Cold is Quiet, Hot is Loud!?!

    This roller rocker business is frustrating. I had Harland Sharp Roller rockers (1.6) that got noisy when the car was hot (.47 lift cam) So, I changed out the lifters and push rods (just in case) and also put on Comp Cam Magnum Roller Rockers (also 1.6). Incredibly, the same result. There is...
  8. 6

    Drone reduction ideas please

    My 96 Cobra vert has twin Flow 40s with an h pipe. It sounds great except for 1900-2000 RPM (severe drone). I have read a few ideas to help: 1. Put Dynamat on the body above the mufflers. I'm not sure how safe this is... 2. Strap something solid and fireproof to the outside of the...
  9. 6

    Roller rocker alignment

    I have more roller rocker noise than I'd like (even though I put in new lifters and adjusted them carefully) so I took off the valve covers and noticed that several of the Proform rocker arm roller tips are not centered over the valve stem tips. How do you move them a few degrees right or left...
  10. 6

    First Time engine build - need 331 advice

    I have a roller block from an Explorer. I want to build it into a low stress, torque biased 331. I have Edel 1.90/1.60 (#60229) heads on my current 302 that I want to use. Will they provide sufficient flow for a 331? What 331 kit is the best - I am not worried about price at this...
  11. 6

    Anyone have an obscure picture?

    This is obscure question, but does anyone have a picture of the inside of the seat on a 68 or 69 where the headrest bracket attaches? I am adding stockers to my 68 low backs. Thanks.
  12. 6

    Should I retorque the heads now?

    I have about 1000 mi. on new Edel Alum heads and I have the valve covers off to adjust the valves (one is ticking). Should I retorque the heads for good preventive measure?
  13. 6

    Very Best Lifter Brand?

    My 302 was rebuilt about 1000 mi ago and two of the lifters bleed down and tick for 10-15 sec at start up. I am going to replace them. What is the best brand - I don't care what they cost. Thanks.
  14. 6

    Seat Options for 68 Vert

    I would like to get stock looking seats with adjustable head rests and some side bolstering for my 68 Vert. Or should I add head rests to the original seats? Also, I have seen comments about differences in the Vert tracks or pans or something... Your ideas are much appreciated, as usual.
  15. 6

    Complete 3G alt Upgrade kit source?

    Basically, I have put a lot of sound system into a car with a newish 63 amp alt. The base notes make the lights dim - I know, its an old story. I am looking for a complete 3G upgrade kit including the alt, brackets, wiring, instructions - whatever is needed for a 68 w/ a 302. I have seen...
  16. 6

    Coil over performance and prices

    I will shortly order a coil over set up for my 68 vert. I want to upgrade the worn out front suspension to get a more predictable ride, eliminate bump steer, adjust ride height, etc. I am looking at Global West, TCP, and Ron Morris ($2500-$3000). In the current economic environment, they all...
  17. 6

    Advanced ign cause overheating?

    Does advanced ignition cause overheating? If so, why? My '68 has a mild cam, alum Edel heads, and the base timing (vac disconnected) is set at 16 btdc and 38 all in at 2700 rpm. With the vac advance connected it goes higher than 55 under no load at 3000 rpm. It will overheat on a hot day...
  18. 6

    Rear main leak options

    My '68 has a '68 block and a TKO 500 trans. About 6 months after installation oil began to drip off the bottom of the bell housing. I did not do the install so I don't know what kind of seal was used or what orientation. The leak is about 4 or 5 drops per night, so really not a ton in a...
  19. 6

    Please correct me on rocker adj

    This is how I think I should adjust a slightly noisy roller rocker - tighten down the nut until the push rod does not rotate easily, then tighten another 1/2 turn and lock it. Sound right?
  20. 6

    Should I glue it on?

    I like the stock rubber pedal covers in my 68, but the clutch cover (new and old) always comes off. Probably because I'm tall and my feet bump the clutch pedal from the back when I get into the car. What do you guys do?
Top Bottom
Back
Forums
Menu