Search results

  1. PickupMan

    Bad PCM or ????

    I finally got my car running with a remanufactured PCM but the problem I'm having is terrible idle, stalling, rough running and a P0102 code for low voltage at Mass Air. I replaced the Mass Air sensor from a running car and same issue. If I put a Volt meter across the two signal wires I get a...
  2. PickupMan

    PATS delete service?

    I picked up a project car and can't get the thing to start. Theft light flashes constantly and continues to flash while trying to start and just want to get it deleted. The car is a 98 GT so if anyone does this service or can recommend a place to send my PCM it would be greatly appreciated...
  3. PickupMan

    Best price on catback for 94?

    Looking for a catback for my 94 GT. Looking at the Flowmaster system 17112. I found one website the other day that had it for $270 shipped but I didn't buy it then and now I can't find it!!! Any other place that has a special going on where I can pick one up a good price? Thanks
  4. PickupMan

    94 GT oil fouled plug

    Ok here's what I got. I purchased this GT last year and put new plugs in it. One of the plugs, can't remember which one, is oil fouled. It might be number 8 but I think it's 7??? Anyway i did some searching and read where if it's number 4 or 8 plug fouled try a new PCV valve. My guess is the...
  5. PickupMan

    94 T5 speedo gear

    Just a quick question. In my 94 GT T5 what number is the Drive gear...7 or 8? Going to be switching over to 3:73 gears and not sure what gear to buy. thanks Joe
  6. PickupMan

    new tires for my new wheels???

    I picked up a set of Bullitt wheels 17 x 9 and 17 x 10.5. My question is regarding the front tires. There is 245/45 R17 in the rims now and they are too skinny and not enough sidewall, for me and was wondering is 275/40 R17 would be OK for the fronts? Also any problems running 315/35 R17 on...
  7. PickupMan

    What's my next step....more power!!

    I picked up a 94 GT to flip and make some money. Well I don't see that happening. The more i see this car sitting in my driveway I just have to keep it!! SO...This is where I stand with mods. The car has a cold air intake and an SLP exhaust. Yep that's it! After fixing the Balancer...
  8. PickupMan

    Terrible Engne vibration

    Got a question regarding engine vibration. Looking at purchasing a 94 GT and the engien damn near wants to jump out of the car. I checked for bad cylinder, spark fuel all is good. I went to check the timing and the marks wern't even close to where true TDC was. If cyl 1 is at TDC rotor is...
  9. PickupMan

    Heads...Stockers OK?

    OK first off I want to say it's been FOREVER since i've been on and sorry about that. Life has taken many turn since my past visit. Anyway I had the stang out today and visited a local car show. While I was there I ran into an old friend and after catching up on old times he asked if i was...
  10. PickupMan

    8" Posi......what one to get?

    OK, the gears are getting pretty noiseyin the rear and it's time to tear them out and rebuild everything...maybe even new gears. Anyway I figured since everything is out I'll install a posi. I don't need anything crazy...heck an old stock limited slip one will work fine but need something...
  11. PickupMan

    What's new int he mustang world???

    Well, I've been out of the Mustang scene for the past 5 years. Still have the Stang just haven't been keeping up with all that is going on. Heck I remember when someone was talking about rack and pinion kits and the net was goign crazy!! Seems like everyone makes a kit now. Just checking in and...
  12. PickupMan

    Wanted: 8" posi

    Looking for a 8" posi unit either the whole diff or just the posi unit. I have the gears I want just need the posi part! Thanks Joe
  13. PickupMan

    Need to know what a 4 speed goes for?

    Ok time to clean out the garage. Before I post it on the classifieds board I would like to know what a 4-speed toploader, tag says it's for a 66 mustang wide ratio, Hurst shifter complate with new steel bushings, flywheel, clutch, pressure plate, I did the 5 speed swap and now it's time to go...
  14. PickupMan

    Fuel line is rotted...what to do??

    Had to use the wife's car today and noticed the smell of fuel when I got out of the car. Took it home and found one of the fuel lines was leaking. Not sure if it's the retun or the feed. But it is wet and rotted. My question is where can I get both fuel lines new? The cae is a 98 V6 but I would...
  15. PickupMan

    Something happened to the new T5 and it doesn't sound good!

    As some of you may know I finally got my T5 installed after taking forever. Well I took the stang out to run her a little and she was breaking up a little so I stepped on the clutch to rev it a little. I reved it to 5k twice and that when I heard it. It sounded like a bearing let loose or...
  16. PickupMan

    5 speed conversion...best money ever spent!

    I finally got the 5 speed in the car after a few months of sitting on jackstands!! Due to lack of time and money this project was put on hold till just recently. Anyway If you are thinking of installing a 5 speed then think no more....DO IT! Man what a differance from the 4 speed. This thing is...
  17. PickupMan

    625 road demon tuning??

    I picked up a 625 road demon card for my 289. The carb is brand new just the guy couldn't tune it so I picked it up for next to nothing. Anyway I installed it on the car today and got it to run but for some reason it idles way too rich and the car will stumble when you go to pull out. Also if...
  18. PickupMan

    headers and t5 clutch cable???

    OK those of you that are running a T5 with a clutch cable and headers, what header are you using? I installed the cable setup and my Flowtech headers are in the way. I have aset of tri-y's hanginf up in the garage just don't want to go through the hassle of installing them and not working. Any...
  19. PickupMan

    In the middle of T5 swap...Help!!

    Ok decided to install my T5...been putting it off forever. Anyway I got everything out and installed the new back plate, flywheel, clutch and pressure plate no problems. Went install the bellhousing (from 93GT) and it doesn't fit???!!! :bang: So I start to measure some things up and here my...
  20. PickupMan

    03 Cobra.....what's the largest size tire??

    Friend of mine has an 03 cobra and want's to install a set of 2000 Cobra R rims, 18 X 9.5 and want's to know what's the largest size tire he can install. Any info would be great. Thanks
Top Bottom
Back
Forums
Menu