Search results

  1. E

    For Sale 1975 Silver Luxury Edition Ghia--original Owner

    One owner 1975 Silver Luxury Edition Ghia. Cranberry interior. Purchased new in Texas and driven only in Texas and Oregon which means no salt/no rust. Time to let it go. I am 70 with bad hip and knee, getting in and out is a chore and the clutch isn't easy on me either. Definitely not a...
  2. E

    1975 Mii Power Steering Rack

    I am original owner of 1975 Mustang II Silver Ghia. I did a total rebuild 3 or 4 years ago.. I did a seal replace on the power rack since it was leaking. I know, it started leaking again in a few months. I took it to a shop who put in a newly rebuilt unit. Original was a three bolt but could...
  3. E

    Lousy background

    How do I get rid of this black background with blue letters. It is a pain to read.
  4. E

    Looking for covers for seat belt anchors

    Looking for of the covers that go over the bolt that holds seat belt to roof in a 1975 Ghia. The 75 were the ones which were rounded and no defined corners. Color does not matter I have the matching vinyl paint I need.
  5. E

    Strong Gas Odor after driving

    My 1975 Ghia emits a very strong gas odor after driving. It dissipates in about and hour and no odor after that. Checked for leaks around carb, fuel lines etc. and found nothing. Suspect the carbon canister since it has never been replaced (original owner). Anyone know where I can get a...
  6. E

    Tow Bar

    In 1979 when I moved from Texas to Oregon I had a tow bar built specifically to tow my 1975 Ghia. I have been cleaning out my shop and just found it. You remove the front bumper with struts and it bolts directly to the mounting holes in the frame. Anyone close to Oregon interested. It cost...
  7. E

    Replaceing Seals in Power Steering Rack

    I have to replace all the seals in my '75 Power Steering rack. Leaks around the shaft to right wheel and from the main body. Parts house sold me an Omega kit 2789 by Corteco. Some of the seals are correct but most aren't. According to Mustang Unlimited info from their catalog I have a TRW...
  8. E

    Couple of electrical questions

    I finished rebuilding a 75 Silver Ghia last year. I purchased it new in 1975. It sat for over ten years before the rebuild and now has about 6000 miles after. I did a total rebuild on 2.8L V6 and the 4 speed tranny. New alternator, starter, PS unit, brakes, etc. you name it I replaced...
  9. E

    Where do you find production statistics

    Where can I find a list of production statistics for the Mustang II? I have a 1975 Silver Luxury Ghia I purchased new in 1975 that I restored last year. Wondering how many were made.--Thanks
  10. E

    Factory Tach interaction with blower fan

    Usually my tach reads about 3000 at 60 mph in 4th gear and 3500 at 70. When I turn on the heater/defroster fan the tach reads higher. The faster the fan is running the higher the tach reads. If the fan is on high the tach reads 600 rpm higher than normal. With the fan on low the reading is...
  11. E

    Vacuum Reservoir Purpose

    I have always understood the purpose of the vacuum reservoir was to keep the vacuum assisted brakes from being erratic. I bypassed mine (temporary patch in the can is leaking) and just put a check valve in the line and it does not seem to make any difference. Brakes work fine, A/C controls are...
  12. E

    Heater control / vacuum system problem

    1975 Ghia with factory air. If heater/AC control is set to Vent air flows OK when the car is idling or running at highway speed. However, when I accelerate the air flow moves to the defroster. After I let off the gas or the car gets up to a steady speed then the air flow goes back to the...
  13. E

    1975 Carb problem---question

    I just finished a total rebuild on my V6 and am having problems getting the carb adjusted correctly. Runs a little rough so you have to crank up the idle to about 900. Had a shop put it on a scope and do their thing. The mechanic told me the throttle plates were not closing all the way, and...
  14. E

    1975 wheels 13" vs. 14"

    My 1975 Ghia came with CR70-13 tires. Rims are 13 x 5 with 4 bolt pattern. The Mustang specs do not list a 14" option for 1975. I have found a set of 14" x 6" chrome rims from a 1979 Mustang. Will they fit and what size tire do I use to make sure I don't screw up the speedometer readings.??
  15. E

    Questions on V6 vacuum system

    I am rebuiling a 1975 2.8 V6 with 4 speed tranny. I have decided to disable the EGR valve and to run the vacuum from the carb straight to the vacuum advance instead of thru the ported vacuum adapter. According to the write up the purpose of the ported vacuum is to directly apply exhaust...
  16. E

    2800cc V6 vacuum system question

    The 2800 V6 (1975, 4-speed with A/C)has a unit mounted in the front center of the engine where the heater and radiator hose connect. It also has the temp sensor and three vacuum control units. Two of the units have three ports and one has two. I am doing a rebuild after 10 years of sitting...
  17. E

    Question on painting vinyl, plastic, rubber

    Wondering if anyone knows of a good paint or dye for the following: Plastic parts like the covers over the seatbelt hangers above your head. Center console lid on a four speed. I think it is come kind of plastic/rubber. Backseat panels that act as arm rests. Mine are cracked bad and need...
  18. E

    Need input shaft for 1975 SR4 transmission

    Looking for an input shaft for a 1975 V6, four speed SR4 transmission. Must be in good shape. Mine has a couple of bad synchro nubs on it.
  19. E

    Need input shaft for SR4 tranny--1975 V6

    Looking for an input shaft for a 1975 V6, four speed SR4 transmission. Must be in good shape. Mine has a couple of bad synchro nubs on it.
  20. E

    1975 Four speed transmission help

    I am trying to put new synchros and input shaft in a 1975 4 speed. I can't figure out how to get the reverse sliding gear off the shaft. I have removed the roll pin on the output shaft and all of the snap rings. I can get all of the gears to spread apart so I can clearly see the gear in...
Top Bottom
Back
Forums
Menu