Search results

  1. Begizzle

    Need help on suspension setup

    I have an '89 notchback. I am wanting to run a wide rear drag radial and skinnies up front. I am wanting to install a 2.5" mac catback with 3" tips, so the tailpipes must clear the wheels/tires. I already have proform upper and lower control arms and stock v8 springs with one coil cut in front...
  2. Begizzle

    Adjusting bumpsteer necessary on a lowered fox?

    So I should be okay by just eyeballing it to make sure that the tie rod end follows the same angle as the lower control arm?
  3. Begizzle

    Tailpipe clearance with panhard bar

    I am looking in to getting Maximum Motorsport's panhard bar. Their website says that it clears factory exhaust and flowmaster. Has anyone installed this with mac exhaust?
  4. Begizzle

    Adjusting bumpsteer necessary on a lowered fox?

    I did a search and found adjusting the bumpsteer two different ways. One was just making the tie rod end level with the bottom of the a-arm and the Second was just making the tie rod end level with the ground. Which one of these is correct and is it really this easy?
  5. Begizzle

    Adjusting bumpsteer necessary on a lowered fox?

    I am installing BBK progressive springs in my '89 coupe. I have heard that it is a good idea to install a bumpsteer kit if you lower your car. I was reading the instructions on how to adjust bumpsteer on Maximum Motorsport's website and it seems very difficult to do. Is it really necessary to...
  6. Begizzle

    5.0Resto's 5-lug conversion

    They say that the rear axles are 25% stronger than stock. Has anyone had problems with these breaking from too much power? And if I wanted to later, can I replace them with 79-93 Moser 5 lug axles or are they a different length?
  7. Begizzle

    Front control arms stuck

    I have a sawzaw. I'll try to do that. I live in Mapleton Depot, PA (central PA). Those pics in my profile are from the previous owner who lived in Altoona, PA. I just bought the car last October and I am doing a lot of work to it over the winter months. I'll be sharing some new pics come this...
  8. Begizzle

    Rear spring removal

    Yah, sway bar and quad shocks removed. I forgot about the brake lines. I'll check tomorrow. That could of been what was holding the rear from dropping farther. I thought that the driveshaft might of had something to do with it. I've also heard of putting a jack underneath the lower control arm...
  9. Begizzle

    Front control arms stuck

    No air tools or torch. I tried smashing it with a hammer and it wouldn't move. Maybe if it soaks in wd40 overnight it will be easier to remove tomorrow.
  10. Begizzle

    Rear spring removal

    I tried putting jack stands under the frame, disconnecting the shocks and dropping the rear end with the jack but the rear end wouldn't drop low enough. Would it help to jack up one side once it is dropped down?
  11. Begizzle

    Hooker roll bar?

    I found this roll bar in a mustang on ebay. It looks very nice. http://cgi.ebay.com/ebaymotors/1984-Ford-Mustang-5-0Lx_W0QQitemZ120075861533QQihZ002QQcategoryZ6236QQrdZ1QQcmdZViewItem I also found it on dallasmustang's website for 480 in chrome. No welding necessary. It is made by Hooker(...
  12. Begizzle

    Front control arms stuck

    I'm currently replacing the front control arms on an '89 lx. I've got both of the rear bolts and nuts removed and I got both front nuts removed, but the front bolts just twist inside the bushings. I've tried hammering but that did not work either. What could I try next?
  13. Begizzle

    Rear spring removal

    I'm installing a set of lowering springs. What is the best way to remove and install the rear springs?
  14. Begizzle

    Trick flow intake manifold

    I am currently running the trick flow track heat intake manifold. Will the street heat upper fit on top of the lower track heat manifold? Do they both use the same lower manifold?
  15. Begizzle

    Roll bar choices??

    I am looking to put a six point roll cage in my '89 notch with either welded in or swing out door bars. Does someone sell them already powdercoated or painted and ready to install?
  16. Begizzle

    4-lug wheel spacers?

    I looked, but did not find them on the website.
  17. Begizzle

    4-lug wheel spacers?

    Does someone make a 4-lug wheel spacer in 1/2" or 1". The only ones that I could find were maximum motorsport's 1/4" spacers. I'm running Ford racing 17x8 cobras and wanted to move the rear wheels out about 1/2 inch or a little bit more.
  18. Begizzle

    CustomWheelsMarket.com??????

    ttt
  19. Begizzle

    CustomWheelsMarket.com??????

    Has anyone on here ever dealt with this company? I was looking to get these wheels for my mustang but the price seemed too good to be true. http://customwheelsmarket.com/cwm-top-1127-7934s.html
  20. Begizzle

    anyone ever used this Impact Gun.....Looking for a new one

    Get the IR titanium. It has 1,000 ft lb. of nut busting torque. I have used all kinds before, and the IR titanium has always worked the best. The 1/2 inch IR titanium is on sale right now at sears through Thursday (11/30) with a free pair of mechanics gloves.
Top Bottom
Back
Forums
Menu