Search results

  1. SAYNOTORICE

    Turbo Gods: Junyard TT setup

    have access
  2. SAYNOTORICE

    Turbo Gods: Junyard TT setup

    I've been doing a lot of thinking about turboing my stang....the junkyard turbo mods have been really making me curious.....what do i need for a tt setup using T3 turbos.....my engine is well maintained but has alot of miles....can my stock heads handle the power?? what do i have to do to my...
  3. SAYNOTORICE

    373 gears VS stock

    90 mustang put it the best.....the feeling is awesome, definitely the most fun mod i have ever done
  4. SAYNOTORICE

    How much $ to install gears

    just noticed you were from mass, go to mike dez'z on rte 6 in seekonk, they do good work there and dez is an awesome guy...very experienced....he has done work on manny buginga's 7 second turbo car (if you follow nmra) so you can be sure you are getting quality work
  5. SAYNOTORICE

    How much $ to install gears

    it cost me $900 including the price of gears to have my rear end rebuilt and a clutch installed....the spider gears were all chewed adn there was metal shaving in the fluid....i had to have a used axle chock from an 03 mach 1 put in my **** was so bad....but now its awesome and i dont have to...
  6. SAYNOTORICE

    how do i find out??

    i see well there is no way the block is cracked cause it would not be running like it is....smoked an lt-1 the other night... :owned: so i guess ill just have to keep it well maintained untill im ready to do it and then get it bored to 306...sounds good
  7. SAYNOTORICE

    how do i find out??

    anybody?? bueler??...dont want this thread to be lost
  8. SAYNOTORICE

    suspension recomendation

    i need to replace my suspension badly....my plan was to replace all the bushings with energy suspension urethane ones...mike dez at DEZ racing recommended ford racing springs, and either KYB's or Tockico blues, it is purely a street car....i know the Tockico's are a bit more expensive, but is...
  9. SAYNOTORICE

    how do i find out??

    I am thinking about rebuilding the engine on my 5.0 next summer rather than buying a new one....how do you determine if the block can be used and where can i find this out
  10. SAYNOTORICE

    making most of my set up

    wouldnt i lose some power goin with one that large however?
  11. SAYNOTORICE

    making most of my set up

    i know the best way to compliment a new intake is a bigger tb and new mass air...with my setup should i run a 65mm tb and 70mm mass air or shouold i go larger???....how about 24#ers??? the engine wiil be untouched for awhile because i need to upgrade the worn suspension, and the body needs some...
  12. SAYNOTORICE

    Att. Newb Intake Installers

    no it was coil i replaced it yesterday morning and it works now...it was big hose that goes into goose neck to t-stat housing so not really one of water pump hoses at all....my b....but there was enough pressure that i heard it pop and bang against the hood and then it splased everywhere off the...
  13. SAYNOTORICE

    Att. Newb Intake Installers

    when installing a new intake manifold be sure to tighten all hoses when finished, especially the water pump hose....if you do not you will be a moron like me and have to buy a a new coil to replace the one you fried :nonono: ....other than that a new manifold is mint so put one in...
  14. SAYNOTORICE

    Intake Install pt 2 Help w/ fuel rails FAST

    ok now i have everything disconected except for the fuel rail to the fuel hose....how do i do this....do i need a special tool??? thanx in advance :hail2:
  15. SAYNOTORICE

    Intake Manifold Install, Need HELP FAST/NOW

    Im in the middle of installing a trick flow street manifold, and i have removed the distributor and the old upper...the haynes manual now says i have to relieve the fuel system pressure, but as i was looking at the procedure one of the steps for relieving the pressure requires the car to be...
  16. SAYNOTORICE

    picked up my street heat intake

    picked up my trick flow manifold today :D ....it is in really good shape and has a 1/2 inch phenolic spacer on it....scored it for $300....i think thats a decent deal....i cant wait to slap this puppy on over the weekend....i have never installed an intake before so i may need help...i know i...
  17. SAYNOTORICE

    cant find this part anywhere..HELP!!

    i need one of the brackets that holds the front sway bar tight and in place close to the chasis.....the right one snapped, and i cant find this part anywhere...the stang is riding like @$S...if you are local (south eastern, MA/RI) and parting out a stang or have this part please post up, or pm...
  18. SAYNOTORICE

    trick flow question

    no hardware included, what do i need to slap that puppy on, im mechanically competent but not too experienced
  19. SAYNOTORICE

    1o5 mm throttle boddie is it a waste of money

    free post :banana:
  20. SAYNOTORICE

    trick flow question

    anybody, bueler??? come on there has to be someone running this intake
Top Bottom
Back
Forums
Menu