Search results

  1. theconductor

    Sensor Ground

    I'm running MSPNP2 and wiring a flex fuel sensor. I have pin 13 wired for the sensor, but I didn't realize that I needed to wire in to the sensor ground as well. Is that pin 22? Also, is pin 22 the only one that will work for the ground? I have a few other leads connected and it would be great...
  2. theconductor

    Fan Controller Question

    I have been using Contour fans with a Derale controller for quite a few years without issue. In the meantime, I swapped out my factory ECU with a Megasquirt PNP. Realizing recently that the MS can be used as a fan controller, would it be ideal to go this route instead of the separate controller...
  3. theconductor

    Remote Tuners for MS

    Now that @a91what has moved on to bigger and better, are there any well regarded tuners able to work remotely to make a few changes in my tune?
  4. theconductor

    Wiring Wideband Into PNP

    I'm getting ready to wire in my plx wideband to the pnp. I believe @a91what told me to use pin21. Do I splice the wire to the wideband into that wire then disconnect my O2 sensors? When that is done, what will I need to do to the software if anything? How will affect my current tune? Another...
  5. theconductor

    351 Hood Options

    Guys and gals, what hoods are you running on your 351 foxes? I'm looking for options and I want to know what will work with the extra deck height.
  6. theconductor

    Fuel Line Question

    So, I was looking under my car for a rattle the other day and I noticed that my fuel lines near the filter are pretty corroded. They need to be replaced. Two questions; How much of a PITA is it to replace the hard lines between the tank and the rails? Secondly, I've searched here and found...
  7. theconductor

    Throttle Body Gasket

    Should I use any sealant along with the gasket? Both TB and EGR. I never have before, but my current car had some blue rtv on it when I pulled it. What are you all doing? Thanks
  8. theconductor

    Smoking Fusible Link

    I've searched on here and found some help, but not exactly what I need. My battery drained, because like an idiot I left the key in the ignition in the acc or on position. I jumped my car and it started fine. As it was warming up I noticed smoke coming from the wires near the solenoid. I'm 99%...
  9. theconductor

    Frozen Door Locks

    I replaced the actuators and the doors still seem to be seized. What else may be causing this? Thanks
  10. theconductor

    Interior Pics - Need Help

    Can anyone send me a few pics of the rear interior hatch of their fox? Specifically where the quarters meet the the back panels. I'm putting the interior back into my car and want to make sure I'm lining it up correctly. TIA
  11. theconductor

    Door Actuator Replacement

    I'm looking for jrichker's article for repairing the door locks. The link is broken. Any ideas? Thanks
  12. theconductor

    Installing Clutch Quadrant

    It seems that the link in the "how to" thread is broken. Anyone have a link to install a quadrant and firewall adjuster? Thanks, Kyle
  13. theconductor

    Engine Valve Cover Leak

    I've got a small leak in the drivers side valve cover. What is the torque spec on the bolts and the preferred order to tighten them? Any other tricks appreciated.
  14. theconductor

    West Coast Sacramento/roseville Meetups

    Anyone gathering in Roseville or really anywhere in the Sac area on a regular basis? Maybe a cars and coffee type of thing? I have access to a large and safe parking lot that we may be able to host a few meetups. Any thoughts?
  15. theconductor

    Aftermarket Coolant Catch Can

    Those of you running electric fans on your foxes, what are you using for a catch can? Also, is there a way to fool the sensor so the low coolant light doesn't come on? Thanks!
  16. theconductor

    Pulley Compatibility

    I'm looking for some stock pulleys for my fox to replace the underdrive set. Are there any other car/trucks that have the same size pulleys as my 92? How about the A/C and power steering pump brackets? Thanks
  17. theconductor

    Belt Sizes

    Does anyone know off hand what size serpentine belt I need for a 1992 mustang without A/C? The tensioner, alternator and smog pump have been relocated after a Vortech install.
  18. theconductor

    North Bay tuners

    I am moving from Portland to Santa Rosa next week. I need to get my 1990 mustang tuned. Can anyone recommend a good shop? The closer to Santa Rosa the better... Thanks, Kyle
  19. theconductor

    Low RPM sputtering

    If I step on the gas when the motor is below 2700 rpm my car sputters and pops a little through the intake. Above 2700 it pulls like a mofo. Could it be the timing? I'm also worried that I'm getting too much fuel at low rpm before the boost kicks in. I have 42# injectors, a 255 fuel pump as...
  20. theconductor

    Supercharger pulley change ?

    I'm running exactly 5 psi of boost right now with my vortech v-1. It has the original pulley on it. Does anyone know what size that would be and what size I would need to go to to get to 8 psi? Thanks, Kyle
Top Bottom
Back
Forums
Menu