Search results

  1. 8

    MAC catback fitment issues

    Everything moves fine, I just cant find a way to adjust it without hitting anything. One way or another its hitting something. was just wondering if anyone had the same issue with this catback and what they did to fix it.
  2. 8

    MAC catback fitment issues

    My car has a MAC catback on it from the previous owner and Im having some issues with it. First off, it doesnt rattle or bang around so thats good. However, the passenger side pipe that goes over the axle is rubbing the control arm and the brake lines. The control arm I can deal with but I...
  3. 8

    Can a clutch slip on deceleration?

    patman - yes, it is very noticeable coming down from higher rpms and down a hill. It feels exactly as you described. Why would they design it like that? Feels horrible, like someone holding the car and then letting it go just like you said. Oh well, at least nothing is wrong with the...
  4. 8

    Can a clutch slip on deceleration?

    That sounds about right too....guess its nothing to worry about either way. Ill make a restrictor plate this weekend anyway as my cars idle does hang a bit. Thanks again guys
  5. 8

    Can a clutch slip on deceleration?

    Thats sounds abou right, thanks for the info. The idle does hang a bit when coming to a stop out of gear. Cleaned the IAC but it didnt make a difference. Ill look into that, thanks again.
  6. 8

    Can a clutch slip on deceleration?

    I have a strange issue with my car. When in gear coming to a stop (off the gas) it feels like the car will come out of gear for a second then get right back in. No wierd noises or anything from the tranny, just feels like its slipping or something in gear coming to a stop. The clutch grabs...
  7. 8

    Can you run Steeda X2 ball joints with stock springs?

    Need to replace my ball joints and was wondering if there was any reason not to run the Steeda ball joints with stock suspension>? Only asking because I have a brand new set from another car I had so I figured why not use them. Would it cause any alignment issues?
  8. 8

    Need some torque specs

    Thanks!
  9. 8

    Need some torque specs

    What are the torque specs for the rack to K-member bolts and outer tie rod ends for a 96 Mustang?
  10. 8

    Anyway to roll odometer forward?

    The cluster went bad in my 96 and I got a good used one with 39k on it, but my actual mileage is 81k. Is there anyway to either roll the new one forward, or just swap the odometers between the two? Its a 96 Cobra if that helps.
  11. 8

    Where to get plug wire covers for valve covers?

    Talking about those black plastic pieces that the plug wires go into before they go into the heads. My car came without them and I would like to find replacements but cant seem to find them anywhere. Any help is appreciated.
  12. 8

    Speedometer Problem

    I installed a Speedcal about a month ago to correct for 4.10's, finally got the switch setting right and the speedo was dead on. However, driving to work today I took an exit ramp and out of nowhere the speedo went to zero but the odometer kept spinning. Then when I got back up to about 60 mph...
  13. 8

    Replacing rack and pinion

    Thanks guys....guess its been a while since Ive changed tranny fluid in one of my GM's. I didnt even know they got past Dexron III, haha thanks for the heads up.
  14. 8

    Replacing rack and pinion

    Thanks wmburns. Dexron III and Mercon V are one in the same, guess Ill just us that. Anyone know how much I might need after taking the rack down?
  15. 8

    Replacing rack and pinion

    Does anyone know about how much fluid I should buy to replace what comes out? Im assuming I just use regular Dexron III ATF, correct?
  16. 8

    Code P0231 what does it mean?

    I just cleared it with the SCT so hopefully it wont come back. How is that destructive to the fuel system? Its essentially the same as pulling the inertia switch in the trunk, which is what everyone else does when they change the filter. Then you simply bleed pressure at the line and you...
  17. 8

    Code P0231 what does it mean?

    Im thinking it wont come back either but if you pull the fuse while its running and let the pump shut down that way there is hardly any fuel in the lines when you go to take the filter off. Works pretty well, except for the code...
  18. 8

    Code P0231 what does it mean?

    Finally got my tuner and its showing this code: P0231 - fuel pump secondary circuit Car runs fine and really dont know what this means, anyone run into this before? I did take out the fuel pump fuse last week while the car was running to change the fuel filter, could this code have been...
  19. 8

    Replacing rack and pinion

    Thanks, not sure what you mean about the teflon seals for the connections. I figured I could just use some teflon tape / pipe sealer. Also, I assume you disconnect them at the rack before you take it off of the subframe, correct?
  20. 8

    Replacing rack and pinion

    Going to replace my rack and pinion, outer tie rods, and steering shaft in a few days. Does anyone have a write-up or any tips for the install? Looks pretty straightforward, just want to make sure im not missing anything. TIA
Top Bottom
Back
Forums
Menu