Search results

  1. jackson0215

    390 Charging Issue

    Morning, I have all of the sudden developed a charging issue. I have a 67 with a 390. 140A single wire alternator, American Autowire harness, after market air and a stern with a single amp. I can charge the battery and leave the car for a week and come back and it will start fine. I go drive...
  2. jackson0215

    Possible Vacuum Leak 67 Mustang

    I finally started my 67 and I have an issue that I think is a vacuum leak but I wanted to see if anyone else had any ideas. It is a rebuilt 390, new comp cap, new Pertronix distributer, new Quick Fuel Carb and Edelbrock intake. When it starts it takes a little feathering to keep it going and...
  3. jackson0215

    67 Steering wheel gap

    I am down to a couple items on the restoration of my 67 fastback and the steering wheel is giving me fits. There is a 1/4” gap between the steering wheel and the column. I have read about adjusting the column and I have tried that but the column hits the bearing at the top and I can’t get the...
  4. jackson0215

    67 390 FE Alternator Issue

    I am in the final stages of finishing up the motor in my 67 and the alternator has brought everything to a stop. I ordered a new bracket kit from CVF racing and when installed it pushes the alternator out past the motor and it hits the battery tray. The adjustment rod won't connect because the...
  5. jackson0215

    67 Spedo Cable

    Evening, I went to install my instrument cluster back into my car and I can not get the speed cable to go into the back. It is a new cable and I unfortunately trashed the old one. The issue is that the metal part that seats into the back of the gauge is hexagonal and where it seats it round...
  6. jackson0215

    SOLD Ssbc Disc/drum Brake Proportioning Valve Ao730

    Brand new SSBC brake proportioning valve. I decided to stick with a stock distribution/proportioning valve. I paid around $85 for it from CJ Pony Parts. Has all 5 inserts and pigtail for the brake lights. I am located in Dallas but I will ship it to you (You pay the shipping). I prefer payment...
  7. jackson0215

    SOLD Ssbc Disc/drum Brake Proportioning Valve Ao730

    Brand new SSBC brake proportioning valve. I decided to stick with a stock distribution/proportioning valve. I paid around $85 for it from CJ Pony Parts. Has all 5 inserts and pigtail for the brake lights. I am located in Dallas but I will ship it to you (You pay the shipping). I prefer...
  8. jackson0215

    67 Instruments Panel Lights

    Anybody know where to find the 2 wire lights for the oil pressure light and the brake light on a cluster harness? If anyone has 2 of them I would also be interested in purchasing them..... Thank you, Mark
  9. jackson0215

    Clutch Question

    Evening, I have a 390 with a 4 speed top loader. I am getting the motor ready to go back in and I not not sure if the ring in the attached picture goes in the place shown or if the bolts go flush to the flywheel. Thank you in advance, Mark
  10. jackson0215

    67 Big Block Clutch Z Bar

    I am trying to figure out how to get the frame side bracket off so I can replace the felt as well as the bushing....Any advice before I tear something up? Thank you as always, Mark
  11. jackson0215

    Steering Column Wiring/american Autowire Kit

    I am putting in an American Autowire kit and they list where 9 wires should go but I have 10 in my original 67 steering column. The mystery one is 511B according to the Ford manual but they do not list it's function either. Not sure what to do with this one since it is not listed in the...
  12. jackson0215

    Vintage Air Power Help

    Good Morning, I am in the process of wiring up my vintage air system and I have a question about the violet wire that is said to connect to the run side of the ignition key.....I also put in an American Autowire kit and it has a heater AC feed. It states that it is a fused ignition power lead...
  13. jackson0215

    Engine Harness American Autowire

    Does anyone have a picture of where they drilled the hole in the firewall for the engine feed on an American Autowire harness? he picture in the instructions is not very clear. I have a 67 Fastback. Thank you, Mark
  14. jackson0215

    What Parts Are These?

    Starting to put things back together and cannot remember for the life of me where these go.....It is a 67 fastbavk with a 4 speed and a 390. Thank you!
  15. jackson0215

    Cj Pony Parts

    I have recently had a number of issues with CJ Pony Parts and I was curious if everyone has had the same issues.....I am finally to the point of putting my 67 back together and ordered ALLOT of parts from CJ. The 2 times I have tried to use my RPM points portions of the order were on backorder...
  16. jackson0215

    67 Mustang 9" Pion Seal Replacement

    I started to replace the pinion seal in my mustang and I need to know how to get the defector out of the rear end without damaging it....I have looked all over and it does not look like you can buy new ones and I looked in my shop manual and it does not state how to remove it....
  17. jackson0215

    Trip Odometer Dials

    I pulled my spedo from my 67 and most of the numbers are gone from the trip odometer dials. Does anyone know if these are a resell part anywhere? I have looked through all of the usual Mustang part houses. Thank you, Mark
  18. jackson0215

    Door Skin.....

    I have some rust in the lower front corner of the passenger side door. The area is about 6" X 6". Question is, would it be better to replace the entire door skin or just the rusted corner? On one hand I hate to trash good original steel but on the other is it better to replace the entire skin?
  19. jackson0215

    Reproduction Doors

    After cutting out the rust on the door skin of my 67 I discovered that the bottom of the door is also rusting out. I am now looking at a reproduction door shell. What is the general experience with these? I planned to use the Dynacorn since the quality and fit seems to be better. My main...
  20. jackson0215

    390 Exhaust Manifolds

    Ok, so stupid question.....I am looking for exhaust manifolds for my 390 (67 S Code) and the heads (C8AE-H) are 14 bolt but everything I see is 8 bolt. FPA has a set of 14 bolt headers and I may go that direction but I am also looking to keep my options open! Does it matter that the heads are...
Top Bottom
Back
Forums
Menu