Search results

  1. gregpro50

    Cant get O2 sensor back in!! What size tread tap ??

    Arent the spark plugs alot smaller than the O2 sensor ?
  2. gregpro50

    bent frame

    If a car drives down the road sideways, doors dont shut right, things dont like up, impossible to align wheels...
  3. gregpro50

    Cant get O2 sensor back in!! What size tread tap ??

    :scratch: I am going to try to figure it out tomorrow. If its not too much trouble can you check and see for me? I hope Sears sells something like that. I have a tool to measure the thread, I just dont know if I will be able to find a tap that is big enough. That O2 opening is a pretty big one.
  4. gregpro50

    Cant get O2 sensor back in!! What size tread tap ??

    Cant get O2 sensor back in!! What size thread tap ?? I pulled the old O2 sensors out of my H-pipe and they came out real hard. Who ever did it last time never used anti-seize. Now I cant get one of the new ones back in because the threads are boogered up. Does anyone know what size thread...
  5. gregpro50

    Injectors

    I just changed all eight on mine. The boiling them in water trick is the way to go. :nice:
  6. gregpro50

    what the heck are these?

    The vacuum canister is for the speed control...
  7. gregpro50

    What to do with a high milage '94 Vert

    205,000 miles ??? That is just broke in for a 5.0 :nice:
  8. gregpro50

    Fuel Injector O-ring replacement ???

    I just got the seal kits from Napa after trying everywhere else is town. Advance auto and Autozone have never heard of them. That boiling them in water trick works slicker than *****. :nice: Only bad part was that my girlfriend came home while I was doing them and thought I was cooking dinner...
  9. gregpro50

    Upper rear axle housing bushing swap

    Has anyone ever changed these ?? I bought an upper and lower control arm set and they didnt come with the bushings for the axle housing. How do you change them ?? Do you whack the old ones out with a hammer ?? They look rusted in there pretty good. Do the new ones need to be pressed in ...
  10. gregpro50

    Bodywork guys, come here !

    The paint code is on the tag on the inside of the drivers door... You can also go to the body paint store and say you want '92 GT red and they can show you a sample of it and all the other reds made in a particular year.
  11. gregpro50

    Fuel Injector O-ring replacement ???

    I am trying to change the O-rings on my injectors so I can swap them into a new intake. I cant seem to change the bottom ones without getting the lower caps off. I already broke one :damnit: Is there a trick to changing the lower O-rings ?? Also, where can I get a replacement cap ?? The...
  12. gregpro50

    BATTERY??

    I hate chasing these electrical gremlins. You can try pulling the stereo and disconnecting all the power wires to see if that stops the problem. I had something similar happen and I had to pull out the factory amp and bypass those wires and it fixed the problem. I still dont know where the...
  13. gregpro50

    BATTERY??

    That is not your problem. You have a hot wire grounding out somewhere. The current from that is over-heating the small ground wire. Usually these problems are caused by improper stereo installation.
  14. gregpro50

    LX tailpipes on a GT ???

    That is exactly what I was thinking :nice: . I think that looks very tasteful. I cant see having any problem with it scraping (unless I can stand it up that far). How did you fab the brackets to drop them down lower ??
  15. gregpro50

    Stupid freakin mustang!!!

    Definitely needs rebuild. Had the same exact problem with another car. I once bought a car from a guy who told me the engine was "rebuilt". It must have been low-budget because it consisted of a couple new gaskets and paint. :bang:
  16. gregpro50

    Help me fix my heater....

    Let the car warm right up and check to make sure the lines going from the engine to the heater core are nice and warm. If so, that means it is something inside the car because there is coolant circulating through the core. If not, then it is something under the hood. Make sure the coolant is...
  17. gregpro50

    Intake gasket question

    The instructions also say to eliminate the end seals and instead to use a 1/4" bead of RTV. Does this sound like a good idea ?? I only want to do this once...
  18. gregpro50

    Intake gasket question

    I cant find the 1250 gaskets anywhere around here. None of the parts stores have them. Summit has them for about $30 including shipping..
  19. gregpro50

    Intake gasket question

    OK I give up, why do aftermarket intake manufacturers recommend the use of Fel-Pro #1250 intake gaskets ?? Why cant I just use the regular Fel-Pro gasket that the parts stores carry ??? :shrug: The intake is a proffesional products typhoon. The car is a '92 GT. I think I remember the...
  20. gregpro50

    84 GT newb Question

    The upper and lower front hoses are the same, and the one that connects the water pump to the thermostat housing. The carbed mustangs had long hoses to connect the heater core to the engine while the EFI ones had two metal tubes that run to the back with two small hoses to connect it to the...
Top Bottom
Back
Forums
Menu