Search results

  1. P

    It's finally alive, also question about a ticking sound

    check your rockers. valve cover clearance, etc.
  2. P

    overheating...again

    hissin, factory gauge, fan and fan clutch im not too sure on, seem ok. im assuming that when the upper hose wasnt tightened down, maybe some air seeped in?
  3. P

    overheating...again

    in the past ive had some overheating problems, i replaced the tstat with a 180* one, got myself a 3 core radiator, and thought the problem would be solved. i dont have a blown head gasket. it runs perfectly while im driving in my higher gears like on a freeway but when i hit the low gears in...
  4. P

    newbie tool question. Ignition switch screws.

    what type of tool do i need for these little guys(2 ignition switch screws) i thought they were the star head drivers but they have a ball in the middle so that doesnt work. how do i get these screws out? :shrug:
  5. P

    pulled distritbutor, replaced without setting at TDC.

    i was swaping the tfi, and i didnt mark the distributor. :nonono: i feel like a jackass.
  6. P

    pulled distritbutor, replaced without setting at TDC.

    is this enough reason why my car wont start and only crank?
  7. P

    need help finding TDC. please.

    ok i pulled out my distributor in order to replace my tfi module, and then i put the distributor backin :nonono: so now i know i need to find TDC and then what? whats the easiest way to find top dead center? i remember reading in one post that i have to crank the engine till there is no(?) air...
  8. P

    water pump?

    who makes a good hi-volume water pump? and can someone explain what i would have to change if it is a "reverse" rotation? is reverse rotation better? thanks in advance.
  9. P

    head gasket installation

    just finished doing this on my buddies H/C/I . dont know how different on a stock stang. obviously disconnect battery. remove upper and lower intake, youll need gaskets for these too. when replacing. remove valve covers, in my friends case roller rockers. remove distributor wires...
  10. P

    starter location?

    how can i diagnose them? my problem is car wont start, i always have to jump it just to get voltage, then i turn the ignition and nothing, before(couple weeks ago) it used to start up then quickly shut off. :shrug:
  11. P

    starter location?

    i want to take it to autozone to get it tested, along with my alt. i dont have the stuff to test it here at home. i think i might have seen it so its on passenger side, kind of mounted on the bellhousing?
  12. P

    starter location?

    :shrug: where is the starter located exactly? is it mounted near my t5 tranny? and whats the best way to uninstall/install?
  13. P

    cobra intake for 200 bux? good deal?

    what does a removable carrier look like?
  14. P

    cobra intake for 200 bux? good deal?

    on another note, is there anyway to tell visually whether its an 8.8 rear end or a 9in? thanks.
  15. P

    cobra intake for 200 bux? good deal?

    i see the stagered runners so im pretty sure its a cobra, what other ways can i tell? o yea and its upper and lower. thanks
  16. P

    cobra intake for 200 bux? good deal?

    hi guys i might be albe to get a cobra intake for 200 dollars, i was wondering what kind of power i can make with this intake when i match it to some nice heads, would i need to port the intake to make good power? or is it already good out of the box? how does it compare to other intakes out on...
  17. P

    help replacing ignition coil.

    dave, it came with that bracket, but i dont have room in my stock engine bay to mount it. Daggar you hit the nail on the head, ill try getting a longer screw, i just thought it was odd that it doesnt just sit back in like i thought it should. thanks for the help guys. p.s. any advice on...
  18. P

    help replacing ignition coil.

    crane fireball. stock replacement, i cant find space to fit the crane bracket.
  19. P

    help replacing ignition coil.

    ok the stock ignition coil is held to the drivers side shock tower by a mounting bracket, i took out the stock coil, the stock coil has a plastic insulator on it, i took it off the stock one and put it on my crane one, thinking that it needed it, i installed the crane coil to the bracket...
  20. P

    help replacing ignition coil.

    bump.
Top Bottom
Back
Forums
Menu