Search results

  1. jruppert

    351w Crate motor what will I need

    I actually purchased a CHP 342 and had absolutely nothing but problems with that engine. I will never order and engine from them again. I ended up purchasing a 351w roller from this place that is mentioned and havent had any issues.
  2. jruppert

    Jumping in and out of closed loop

    I am trying to help someone tune their maf but his setup keeps jumping in and out of closed loop. How do I stop this? I havent had this issue with my car. It seems like when it goes into open loop the load is way low.
  3. jruppert

    351w what roller came should I go? b303 e303 etc?

    Yeah I have been leanin towards the tfs 1 cam. I know with the 1.7's it will bump the lift from .499/.510 to .530/.542. Do you think this will effect the power band much?
  4. jruppert

    351w what roller came should I go? b303 e303 etc?

    My future plans are to stroke that one out to a 393. At that point I would definitely want to upgrade the heads. The 185's may be peakin out with the 351. Although with a small cam I doubt if I am pushing them that hard. TFS 2 cam is what I had. It was a good cam. I am concerned about the...
  5. jruppert

    351w what roller came should I go? b303 e303 etc?

    I had a 342 but threw a rod and so now I am building a 351w. I am on a budget at the moment so I needed to start with a budget 351w. This setup has AFR 185's, 75mm, rpm intake, 30lb injectors. My original cam was a TFS 2 cam .542/.563. This cam was damaged when the rod broke. So now I need...
  6. jruppert

    351w swap.. what long tube headers can I use?

    The only problem I had when I went to the Mac 79-93 headers was that I needed to grind a little on the K-member. After that I had no issues. The cost of 351w swap headers are a bit high and I am on a budget. That is why I wondered what all would work. I am not even sure if a set of 79-93...
  7. jruppert

    351w swap.. what long tube headers can I use?

    I posted this in 94-95 section. Thanks
  8. jruppert

    351w swap.. what long tube headers can I use?

    I am in search of some used long tube headers for my 351w swap. What years will work? I have a 94 Mustang and have been able to get away with 79-93 Mac long tubes for my 347. Are there 351w headers from pre 79 mustangs or trucks or anything that could work? I reason I ask is because I believe I...
  9. jruppert

    351w swap.. what long tube headers can I use?

    I am in search of some used long tube headers for my 351w swap. What years will work? I have a 94 Mustang and have been able to get away with 79-93 Mac long tubes for my 347. Are there 351w headers from pre 79 mustangs or trucks or anything that could work? I reason I ask is because I...
  10. jruppert

    Need new distributor gear for 351w roller- what part number??

    thanks for the info. i was told that since i got it out of a 96 that it should already have the steel gear. i need to take a look at it and find out for sure before dropping it in there.
  11. jruppert

    Need new distributor gear for 351w roller- what part number??

    anyone?
  12. jruppert

    fox body long tubes in an sn95?

    Well the biggest difference will be that the fox headers have no EGR hookup. I have a set of MAC long tubes on my 94. They will fit. I had to grind out a little bit on the bottom of the K-member. It wasnt a whole lot. Other then that I had no fitment issues. I had to bring the headers up...
  13. jruppert

    Need new distributor gear for 351w roller- what part number??

    I am in need of a different gear for the distributor since I am putting a roller cam in this 351w roller block. The distributor I got was out of a 96 351w. Since I need to change the gear do you know what part number it is? Ford Racing shows this part number: M-12390-F Steel Yellow...
  14. jruppert

    any roller 351w users? what cam do you have?

    I want this to be a streetable cam. I wonder if the TFS 2 cam that I need to replace would be a decent one for the 351. Here is my setup: 351w RPM intake, 75mm throttle, 77mm pro-m, 30lb injectors, mac long tube headers, 3.73 gears, tweecer
  15. jruppert

    any roller 351w users? what cam do you have?

    I am in search of a cam for my 351w. It needs to be a roller cam. What do you guys use and what would you recommend? I have a TFS 2 cam but needs to be replaced since my 347 blowup.
  16. jruppert

    questions about 351w lower intake

    Thats pretty much what I wanted to hear. I figured at worse I would need to clean up the ports a going to the heads. What about an upper intake? I thought about maybe selling both upper and lower and getting a polished version since they are inexpensive.
  17. jruppert

    questions about 351w lower intake

    I am doing a 351w swap and will be needing to change my lower intake. Currently I am using an RPM upper and lower and I plan on staying with the RPM upper. Since I need to change the lower, should I go with Edelbrock or is it safe to go the Typhoon style intake? I would just as soon go the...
  18. jruppert

    351w pistons

    My 342 went south on me and I am looking into the idea of using a 351w and staying with the standard cubes. Could I get away with using a roller 351w and rebuilding it but replacing the pistons with something that will work with my heads? I am using AFR 185's. I dont have a lot of money to...
  19. jruppert

    what happened to my 342 stroker?

    i will get some pics today. when looking at the piston, you will see about 20 marks or so in the area where the valve would be coming in. On the head, you can see somewhat of a marking but it isnt really bad. It doesnt even appear that the valves are hit. I am sure they are though. There is...
  20. jruppert

    what happened to my 342 stroker?

    There was around 10000 miles on the engine. I have had it since 03. I have had many problems with this engine. Originally it came from them as a balanced short block. Right away we had issues but soon realized that the balance was off and caused the bearings to go out. We called CHP and...
Top Bottom
Back
Forums
Menu