Search results

  1. 4dStang

    AAHHHH!!!! HELP!!!! I WIPED OUT!!!!!

    The repercussions of goofin off. I took a curve on a dry road about 45 and went a little to far out. Luckily it was in a new housing area and was just dirt. I did hit a stick and cracked up the clear on the lower rocker but lucked out. If I were you, I would either ship out the wheel to...
  2. 4dStang

    Why must you die?

    I learned that my Cobra ran like crap with the 24 LB maf tube on my C&L. I changed it to the 19LB and it runs GREAT. But I had popping problems with the incorrect tube, not stalling issues. I too would also first look at the base idle speed with that different cam in there. But you do need...
  3. 4dStang

    Which H-Pipe??

    I have a prochamber with eq length shorty Mac headers and Flowmaster catback sys. I took off the H pipe, installed stock cats and like the sound better than with the prochamber. But for setup and install, the prochamber bolts together and is adjustable so you can get it up higher than some mid...
  4. 4dStang

    just had the 3.73's installed!!

    Subframe connectors may be a great mod but there are tons of great mods. In fact you can go bankrupt putting on mods and then have someone in a daze smash into your car and then subframes are moot. At least after a crash I can take out all my power adders before the ins co gets the car. :D...
  5. 4dStang

    instrument panel schematics- Please help

    Can anyone give me the scematics that would include the Tach for a 95 Mustang/Cobra. At the minimum I would like a link. I have a flat tach until you rev off idle and it works fine until it drops back to idle. I'm hoping it's not the actual gauge because it has the Cobra white face gauges...
  6. 4dStang

    exhust problems!!!! hangs low

    If your lowered and have long tubes, you'll have to fix it at a muffler shop and just live with it unless you have shorty headers. Even My H-pipe rubbed with shortiy headers. My car is lowered and hits pebbles as it drives down the road. Just my fact of life. Not sure if I am going to lower...
  7. 4dStang

    pics of vaccum diagram

    You got one of those emissions/vacuum line charts for a 95 mustang/Cobra? I like to know everything. I even have a T-5 manual jsut to understand. Thanks Chris
  8. 4dStang

    just had the 3.73's installed!!

    What if he doesn't race, what do sub frames help. Maybe he just wants a good acceleration like I do. I have modded everything else and skipped the subframes until I am ready for the track. Then I will put on a pair of subframes.
  9. 4dStang

    Help with Autometer gauge

    When I did my gauges, I just went to an auto parts store that had many brass fittings. I did one for the water and for the oil. I just pieced it together after a few minutes and a little help with all senders. I have to do it again in a week myself since I have new gauges for my new car. That...
  10. 4dStang

    Squeak, Squeak, Squeak, Squeak....

    OK, From experience! If you have drum brakes, make sure the shoe is not rubbing by backing them out or turning the drums. If you have rear disks (SN95+) One may be warped, just buy a new one. I WOULD check that first by jacking up the car so only one wheel can spin, have someone drive...
  11. 4dStang

    PROBLEM: Transmission or Clutch - Ideas?

    Maybe pull the console out and look at the shifter and mount, remove it, and look inside. Also, change that tranny fluid first. It may be low, and under stress, then maybe the gears will start to whine. Not from experience, just guessing. Other wise, you may have a bad bearing in the trans...
  12. 4dStang

    just had the 3.73's installed!!

    How much HP do sub frames give you. Gears are the bomb for speed but once you start modding, You have to add this, or that, or maybe a couple of those. Before warned of the snake too. That f-er bit my as$ bad! Have fun #1
  13. 4dStang

    headers worth it on stock setup?

    373 are the second mod anyone with a Mustang/Cobra should do. First of course exhaust!!!
  14. 4dStang

    PROBLEM: Transmission or Clutch - Ideas?

    Can you jack it up and have someone spin the rear wheels and you slide under to get a closer point of origin of the sound? Hard to troubleshoot a noise on a forum. I would check the drive shaft bolts and make sure everything was tight underneath. At this point I can only tell you to throw...
  15. 4dStang

    show me some pics

    I was set to buy this car a month ago. I chose to get a black HT instead for $750 less in Chicago. My wife told me I should have bought the white one! Enjoy!
  16. 4dStang

    taking out stock h pipe....

    I have done the swap for smog so many times that it takes longer to put the car on jacks than it does to r/r the mid pipe. Just keep the bolts clean, the more you swap out the parts, the easier it will get. I am just waiting for my smog card here in IL so I can thow in my prochamber. An...
  17. 4dStang

    Would gears require changes to Speedo?

    You would think that but I have tested it at many radar sites and no matter what speed I go, it is seven! Been there and tested it. If you don't believe me...... Been driving it that way for 2 years and it has always been seven. I was confused and thought the speed would change the faster...
  18. 4dStang

    Vibration is still there!!! Please help me before I give up and sell the car!

    I recently bought a 95 Cobra and found it to pull to the right like crazy and had a bad shimmy over 55. I had it aligned and it was perfect. I swapped out a different set of tires/wheels and it was perfect. My conclusion is that I had a belt in a cheap tire that waas separating. I sold the...
  19. 4dStang

    Cobra Gt-40 NOT P...casting # #F1ZE AA

    GT 40P heads do not look like Cobra heads. They are stamped with a P some where on there. I just can't think of where it is because I would never get a set and never payed attention.
  20. 4dStang

    Cobra Gt-40 NOT P...casting # #F1ZE AA

    I just sold a pair of F1ZE and they were for sure GT-40 heads. In my findings, the cast iron is just heavier and will give you great performance especially if they are ported out. The aluminum is just lighter or may have bigger valves which means you will have to fly cut your pistons. I like...
Top Bottom
Back
Forums
Menu