Search results

  1. MikeR351w

    Fuel Rail Bolts????

    Ok Ill stop into a hardware store tomorrow night and see if they can get one. Thanks
  2. MikeR351w

    Diagnose Dripping Oil Leak?

    Yikes. My 93 Leaked from the same spot. I changed the oil pan gasket with the engine still in the car. It was very hard to do but I did it. Afterwards, the leak slowed down quite a bit. It still was not gone completely. I think mine was the rear main seal. so I would assume yours is too...
  3. MikeR351w

    Fuel Rail Bolts????

    any suggestions would be appreciated. I got these aftermarket rails. Unknown brand. They were on a fox mustang 5.0 so i dont know why the bolt holes hug the rails so close. A standard bolt wont turn because the 5 point part of the bolt head hits the rail. What should i do?
  4. MikeR351w

    Engine Best Harmonic Balancer...

    Yes, motor is balanced , crankshaft and pistons balanced so I assume its Internally balanced then.
  5. MikeR351w

    Engine Best Harmonic Balancer...

    I have a R302, stroked to 331. I got about 7k in the engine. I have a cheap balancer (chineese junk) and want a better one. Any suggestions? I need one that will not use any adapters if possible. Thanks!
  6. MikeR351w

    Engine 50oz Balancer Bolts...

    I just read that this balancer is garbage. Im going to buy a new one. Any suggestions???
  7. MikeR351w

    Engine 50oz Balancer Bolts...

    Pics
  8. MikeR351w

    Engine 50oz Balancer Bolts...

    Pic
  9. MikeR351w

    Engine 50oz Balancer Bolts...

    HBF-302-HO CAL Auto Transpeed is engraved on it
  10. MikeR351w

    Engine 50oz Balancer Bolts...

    Yes, the four bolts that bolt the pulley to the balancer. I have an aftermarket balancer. Its an old one with a Cat on it. It is a 50oz balancer so its not stock. My stock balancer bolts do not work. The threads dont match.
  11. MikeR351w

    Engine 50oz Balancer Bolts...

    Hello I have a 50oz balancer on my 302 setup. I cant seem to re use the stock crank shafter bolts. they dont fit for whatever reason. Anyone know if they are a different bolt from the factory balancer???
  12. MikeR351w

    Tf Aluminum Heads Ported, What Ex. Gasket To Use?

    It was easier to measure accurately with mm than inches. My gasket is too small but not much room for porting or trimming it. The headers are shorties from bbk.
  13. MikeR351w

    Tf Aluminum Heads Ported, What Ex. Gasket To Use?

    Here is one pic.
  14. MikeR351w

    Tf Aluminum Heads Ported, What Ex. Gasket To Use?

    Would the smaller gasket interfere with the exhaust flow? Or would it not be worth trimming?
  15. MikeR351w

    Tf Aluminum Heads Ported, What Ex. Gasket To Use?

    Hello, I have a 90 LX 5.0. Long story short, the Trick Flow Aluminum heads were ported and flow a ton of air. Bad news is I took my exhaust gaskets up to them and they are too small now. There is not much room for trimming them wider. They fit the height but the width is now 5mm too large...
  16. MikeR351w

    Custom Fuel System Setup Assistance Help!

    Ok. Do you think I should drop down to a single pump for now or install both? I can definelty wire in the inertia switch too. Ill buy a kit from Aeromotive. Thanks so far.
  17. MikeR351w

    Custom Fuel System Setup Assistance Help!

    Hello, I have attached my proposed diagram for my setup. Keep in mind, I bought the system with the car and it came off of a Fox Body 5.0 and is going onto my 1990 5.0 LX hatch. The main line is -8 and the return from the rail to the regulator is -6 fittings. I got all the parts together and...
  18. MikeR351w

    Engine Vortech Sc On Stock Fox Long Block

    I had a V1 on my 93 LX for two years and beat it up pretty good with the stock gaskets. I had a small pulley on it and it had around 12lbs of boost. Stock AOD too.
  19. MikeR351w

    Fuel issue: 92 LX Vortech V1 w/wideband gauge

    I am listening to the advice. I re-hooked up my FMU and it gave me some better reading with my a/f ratio and I am looking for stock o2 sensors with a harness. Thanks for everyones help :)
  20. MikeR351w

    Fuel issue: 92 LX Vortech V1 w/wideband gauge

    Ill try to answer all of the questions. Yes, I did gap my plugs to 35 and got new ones. Also, the Mass Air meter IS calibrated to the injectors. Since I currently dont have any stock o2 sensors, the wideband is hooked up to the autometer gauge. Its a Cobalt wideband. Ill hook up the FMU...
Top Bottom
Back
Forums
Menu