Search results

  1. jackson0215

    390 Hooker Headers

    Has anyone used Hooker Headers for a 390 in a 67 mustang? Years ago my dad cut out the rear fender aprons to fit them and I am hopeful that they now make them so that they fit. HOK-6114HKR 67, fastback, 390 and a 4 speed. Thank you
  2. jackson0215

    351W Stroker vs 390

    I believe they also used a different set of shock towers for the big blocks, at least they did in 67. DH is right, big blocks have a cool factor but everything I buy costs my allot more than what the same part for a 351 is. Good luck..
  3. jackson0215

    Cowl Rustproofing

    Hello, I see allot of posts on fixing a rusted out cowl area but my questions is about one that is not rusted out. I would like to figure out a way to retreat the area inside the cowl without cutting anything apart. I do not plan to leave the car outside but getting all of the rust out of the...
  4. jackson0215

    Torque box - Shoulda bought a 2 piece

    By the way, if you are replacing the rear fender aprons, replace them BEFORE you put in the torque box.....Don't ask how I know!
  5. jackson0215

    Toe board fit-up 67 coupe

    I just replaced mine in a 67 Fastback and it was a nightmare. I actually had to purchase another one for the driver side since I screwed up the first on so bad. They try to make these for multiple models and applications and they take a fair amount of modifications to fit them together. Mine...
  6. jackson0215

    Rocker Arms

    As always thanks for the help, they put in new lifters, rods and rocker arms when it was rebuilt.
  7. jackson0215

    Rocker Arms

    I was looking at the Comp High Energy Hydraulic Flat Tappet Cam... Thanks
  8. jackson0215

    Rocker Arms

    Sorry about that.....390 with stock rebuilt heads, Edelbrock performer intake and Holley Carb. They did not do much else to it. I assume the compression is what it was stock.
  9. jackson0215

    Rocker Arms

    Question....I am wanting to change out my cam which means new push rods and, hydraulic lifters and new rocker arms since mine are non-adjustable. The questions is can I use new roller rockers arms on the stock shaft and stands? All I have heard about the aluminum stands is that they can...
  10. jackson0215

    Valve Train Question

    I recently purchased a rebuilt 390 and it has the stock cam, and stock rockers. I would like to replace the cam and I really like the Thumpr series from Comp but I am not sure if I am getting in over my head. The rockers are not adjustable so I would like to swap them along with the lifters if...
  11. jackson0215

    Where can i get a complete granada break system...

    If you are dead set on replacing them use these guys.... Welcome to CSRP I did the junk yard swap for a 67 and in the long run it is costing me more.....
  12. jackson0215

    Suspension Rebuild on a Budget

    One thing to remember is that if you do this yourself you need to be extremely careful when removing and installing the springs. Do not give into temptation and use an impact wrench to compress them, it is not worth the busted knee caps (or worse)that you will endure.
  13. jackson0215

    Suspension Rebuild on a Budget

    You are better off replacing everything. The parts are not too expensive as long as you stay stock. If you piece it together you will be in an endless cycle of replacing parts.
  14. jackson0215

    67 speedometer rebuild

    Good point, Any thoughts on fixing the trip dials?
  15. jackson0215

    67 speedometer rebuild

    Has anyone rebuilt a speedometer for a 67 and is there anything to pay extra close attention to? The trip dials in mine are not lining up right and since I am putting a new engine in I would like to put it back to 0. Thank you in advance!!
  16. jackson0215

    390 Block Spacer

    Perfect, thank you for helping clear it up. It looks like it is the same plate for both automatics and manuals.
  17. jackson0215

    390 Block Spacer

    It does have a removable "adjustment" cover. Some of the other spacer that I have seen have a larger hole at the top instead of the three holes.... http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=130350390762&ssPageName=STRK:MEWAX:IT#ht_500wt_1182 Thanks
  18. jackson0215

    390 Block Spacer

    Following is a pic of the plate. It also has a code of 4 10 D 3 Thank you for all of the help!
  19. jackson0215

    390 Block Spacer

    I recently purchased a 390 big block and it came with the block spacer and flywheel for an auto transmission. I have a 4 speed manual but I am not sure if the block spacer is the same for the automatic as the manual? I have seen pictures on-line with the description noting it both ways...
  20. jackson0215

    Brake Proportioning Valve

    Thanks for the information. I was hoping to use it for a conversion. The picture is pretty close, the bracket is different. Thanks again
Top Bottom
Back
Forums
Menu