1.7's?

87street

New Member
Sep 17, 2008
33
0
0
Hey guys I've gotta tech question, that may sound rather ignorant, and may be a matter of opinion, but what kind of benefit may I see if I install 1.7 roller rockers? over the factory rockers on my 5.0? I plan on running a comp cam:
264/270 adv duration
212/218 duration at .050
.512/.512 lift
114 lsa

I was figuring this cam with a set of mildly ported e7's, and a ported factory intake, with 1 5/8 inch headers and a 70 mm tb, ought to be a nice running combo.
But then I noticed some people were preferring to run 1.7 rockers, and I guess that would increase the factory lift by .030? or so? And how would my rpm range be affected? All help is greatly appreciated, and this is just going to be a build I'll run for the next couple years, give or take a little bit, as another user has already helped me establish an aluminum headed-solid roller, stroker build up. However, my pockets are only "so deep" right now.
 
If you're going with an aftermarket cam anyway, just go with a set of 1.6 ratio roller rockers and let the cam the amount of additional lift. The 1.7's are for guys with stock cam profiles who are looking for a little added lift on a budget, without tearing into the engine.

Increasing the rocker ratio will generallly place additional side load on the valves, which over time will wear away at your valve guides. The effect is minimal with the stock cam, but is further augmented when you increase the lift with both the cam and the rockers.

A .030 bore won't make a difference either way, so don't be concerned about it. :nice:
 
The 1.7s will increase your airflow slightly, but the big benefit over stock is the reduced friction and increased valvetrain stability. The stockers are sled-fulcrum type, and create a significant amount of friction compared to a similar roller rocker. RRs are supposed to be easier on your oil for that reason. Expect HP gains to only be in the 5-10ish range on a mild motor.
 
1.7's can be a good mod, but you've got to watch your piston to valve clearance issues with that aftermarket cam. You need .100 on the exhaust and .80 on the intake at a MINIMUM or you will bend pushrods.

Contrary to what some people think, the roller tip on the rocker by definition can not put any loads perpendicular to the valve stem. Thus they will in fact have LESS wear on the valve guides than a conventional rocker which creates perpendicular loads due by means of the metal to metal friction at the tip of the rocker and the valve stem.

I've got a used set of the non-adjustable Crane's if your interested - pm me.

Good luck..
 
Hey guys I've gotta tech question, that may sound rather ignorant, and may be a matter of opinion, but what kind of benefit may I see if I install 1.7 roller rockers? over the factory rockers on my 5.0? I plan on running a comp cam:
264/270 adv duration
212/218 duration at .050
.512/.512 lift
114 lsa

I was figuring this cam with a set of mildly ported e7's, and a ported factory intake, with 1 5/8 inch headers and a 70 mm tb, ought to be a nice running combo.
But then I noticed some people were preferring to run 1.7 rockers, and I guess that would increase the factory lift by .030? or so? And how would my rpm range be affected? All help is greatly appreciated, and this is just going to be a build I'll run for the next couple years, give or take a little bit, as another user has already helped me establish an aluminum headed-solid roller, stroker build up. However, my pockets are only "so deep" right now.

An engine with E7's, even mildly ported, will not flow enough air to benefit from a bigger cam. I suggest you keep the stock cam until you're ready to buy better heads.
If you have good DIY porting skills, you can port your existing E7s and intake (as I did) to gain a few ponies. You could even opt for 1.7 roller rockers to increase the valve lift from the stock cam (~4rwhp/3rwtq gain) but keep in mind that if you change heads/cam later on, you could run into piston-to-valve clearance problems with some aftermarket cams.