• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

2.5" H-pipe w/ factory headers?

  • Thread starter Thread starter caseywan
  • Start date Start date Mar 13, 2007
C

caseywan

Member
Apr 7, 2006
157
0
17
Chicago, IL
Mar 13, 2007
#1
  • Mar 13, 2007
  • #1
Will, a 2.5" O/R H-pipe bolt up fine to factory headers. Thanks in advance.
 
8

89bluegt

New Member
Jun 21, 2003
95
0
0
SC
Mar 13, 2007
#2
  • Mar 13, 2007
  • #2
Yes, it will bolt right up.
 
C

caseywan

Member
Apr 7, 2006
157
0
17
Chicago, IL
Mar 13, 2007
#3
  • Mar 13, 2007
  • #3
Ok, thanks. Just wanted to make sure b4 I start tearing apart stuff.
 
C

caseywan

Member
Apr 7, 2006
157
0
17
Chicago, IL
Mar 14, 2007
#4
  • Mar 14, 2007
  • #4
I got it on, but for the life of me couln't get the h-pipe to seal to the collectors! I put washers in as spacers before the nuts and is still leaking.

Any suggestions??
 
8

89bluegt

New Member
Jun 21, 2003
95
0
0
SC
Mar 14, 2007
#5
  • Mar 14, 2007
  • #5
I had trouble getting a set to seal one time and it was because the opening on the H pipe was the same size as the hole on the header. I took a hammer and tapped the opening on the H pipe all the way around the hole to close it a little.
Hope this helps.
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Mar 14, 2007
#6
  • Mar 14, 2007
  • #6
just going to have to play with the 2 of them to get them to seal.
 

Darkwriter77

Resident Ranting Negative Nancy
5 Year Member
Jul 1, 2005
315
283
134
Apache Junction, AZ
Mar 14, 2007
#7
  • Mar 14, 2007
  • #7
I've heard some guys recommend using some high-temp copper RTV silicone around the flanges before you push it all up there and cinch it down. I haven't tried this, myself, and I suspect that it's possible the stuff would just be blown right out (especially if you don't allow it enough time to fully cure), but it's worth a shot. You'll only be out, what, five bucks for a tube, and you can rub it right off with your thumb if it doesn't work for ya'.

Alternatively, you could probably do the same and maybe have better luck with a tube of that "muffler mender" goop, but it sets up a lot faster, so you'd better be quick about bolting stuff together after you put it around the flanges. Again, it's not terribly permanent and forever-binding like JB Weld or anything, it's just kind of a clay putty sort of stuff, but it's also worth a shot.

Interesting that you should mention using washers to help push the flanges together. I kinda suspect mine is leaking a bit at the header flanges, although I can't for the life of me figure out where (can't feel a leak by hand or by waving a tissue around to feel for a leak), but I've been about gagging from exhaust fumes for the past year or so ... even after changing from one brand of X-pipe to another! So, I might give that a try for giggles - thanks for the idea!
 
You must log in or register to reply here.

Similar threads

Engine Would you replace these OEM motor mounts?
  • 91GTstroked
  • Sep 21, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
421
Fox 5.0 Mustang Tech Oct 11, 2026
Potomus Pete
M
Off-road h pipe
  • MadMatt7
  • Oct 17, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
348
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 10, 2026
nickyb
New Exhaust for 408w stroker
  • SadbutTrue
  • Sep 10, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
1
Views
174
1965 - 1973 Classic Mustangs -General/Talk- Sep 10, 2026
nickyb
M
My numbers sound right?
  • MiltP
  • Feb 25, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • 2
Replies
28
Views
1K
1996 - 2004 SN95 Mustang -General/Talk- Apr 2, 2026
MiltP
M
C
Need MIL Eliminators?
  • crazyone64
  • May 18, 2026
  • SN95 4.6L Mustang Tech
Replies
3
Views
315
SN95 4.6L Mustang Tech May 21, 2026
GOvert
G
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?