• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

302 rebuild.

  • Thread starter Thread starter bentley429
  • Start date Start date Jul 20, 2006
B

bentley429

Banned
Nov 25, 2004
528
3
0
Connecticut
Jul 20, 2006
#1
  • Jul 20, 2006
  • #1
This fall/winter Iam planning a rebuild for my 89. I bought a rebuilt shortblock for a good price not to long ago that I will be taking apart just to make sure everything is ok. It is a stock rebuild with a custom grind Comp cam. Specs of engine are:

"1990 5.0ho block, forged piston, stock crank and rods, melling hv oil pump and pickup, arp pump shaft, edelbrock timing set dual roller, timing cover, new water pump, all new bearings and seals, block was cleaned and inspected at the machine shop, comp custom grind cam, roller lifters, and pushrods

cam specs int. exh.
gross valve lift .513 .513
duration@.050 224 230
adver. duration 276 282
lobe seperation 114.0"


Iam currently running a Powerdyne at 6 psi, edelbrock performer intake, 70 mm tb, full exhaust, roller rockers, etc.....As far as I know stock heads. Now Iam looking to make around 425 rwhp and run high 11's. Iam debating between Twisted wedges and AFR's, and not sure if my intake will be enough. Hopefully I will be swapping out the powerdyne for a S trim at the same time. I have seen many different combos but Iam not 100% sure what is right for me. Remember I want to keep the power below the block splitting point so if say a Novi 1000 is enough(without overspinning it), or keep running the powerdyne with a 2.93 pulley is a good idea let me know. Another thing is head gaskets, with running a supercharger what are the BEST headgaskets to use and what material are they made with. Thanks
 
D

DeVus1

Founding Member
Mar 29, 2002
400
2
28
P-Town, Va.
Jul 20, 2006
#2
  • Jul 20, 2006
  • #2
Fel-Pro gaskets, imho, are the best gaskets on the market.
 
B

bentley429

Banned
Nov 25, 2004
528
3
0
Connecticut
Jul 20, 2006
#3
  • Jul 20, 2006
  • #3
DeVus1 said:
Fel-Pro gaskets, imho, are the best gaskets on the market.
Click to expand...

Which ones exactly do you think are the best ones, material wise.
 
D

DeVus1

Founding Member
Mar 29, 2002
400
2
28
P-Town, Va.
Jul 20, 2006
#4
  • Jul 20, 2006
  • #4
http://store.summitracing.com/partd...11-2&N=4294908331+4294840126+115&autoview=sku
 
B

bentley429

Banned
Nov 25, 2004
528
3
0
Connecticut
Jul 20, 2006
#5
  • Jul 20, 2006
  • #5
DeVus1 said:
http://store.summitracing.com/partd...11-2&N=4294908331+4294840126+115&autoview=sku
Click to expand...


How about copper vs steel? Those headgaskets dont seem to be for a high performance engine. Dont want to cheap out.
 

Foxfan88

My Grandpa has great wood.
Sep 13, 2004
2,487
4
0
Miami, Ok
Jul 20, 2006
#6
  • Jul 20, 2006
  • #6
i've heard if u have a stock oil pan, to run a standard pump. as a HV pump will suck your oilpan dry at high rpm....
 

GearHd6

Member
Jul 19, 2005
459
0
18
Ashford, CT
Jul 20, 2006
#7
  • Jul 20, 2006
  • #7
Foxfan88 said:
i've heard if u have a stock oil pan, to run a standard pump. as a HV pump will suck your oilpan dry at high rpm....
Click to expand...

 

Foxfan88

My Grandpa has great wood.
Sep 13, 2004
2,487
4
0
Miami, Ok
Jul 20, 2006
#8
  • Jul 20, 2006
  • #8
which wouldnt be a good thing hehe
 
B

bentley429

Banned
Nov 25, 2004
528
3
0
Connecticut
Jul 20, 2006
#9
  • Jul 20, 2006
  • #9
Thanks for the info guys, keep it coming.
 

Killer50stang

New Member
May 11, 2004
632
0
0
Jul 20, 2006
#10
  • Jul 20, 2006
  • #10
bentley429 said:
This fall/winter Iam planning a rebuild for my 89. I bought a rebuilt shortblock for a good price not to long ago that I will be taking apart just to make sure everything is ok. It is a stock rebuild with a custom grind Comp cam. Specs of engine are:

"1990 5.0ho block, forged piston, stock crank and rods, melling hv oil pump and pickup, arp pump shaft, edelbrock timing set dual roller, timing cover, new water pump, all new bearings and seals, block was cleaned and inspected at the machine shop, comp custom grind cam, roller lifters, and pushrods

cam specs int. exh.
gross valve lift .513 .513
duration@.050 224 230
adver. duration 276 282
lobe seperation 114.0"


Iam currently running a Powerdyne at 6 psi, edelbrock performer intake, 70 mm tb, full exhaust, roller rockers, etc.....As far as I know stock heads. Now Iam looking to make around 425 rwhp and run high 11's. Iam debating between Twisted wedges and AFR's, and not sure if my intake will be enough. Hopefully I will be swapping out the powerdyne for a S trim at the same time. I have seen many different combos but Iam not 100% sure what is right for me. Remember I want to keep the power below the block splitting point so if say a Novi 1000 is enough(without overspinning it), or keep running the powerdyne with a 2.93 pulley is a good idea let me know. Another thing is head gaskets, with running a supercharger what are the BEST headgaskets to use and what material are they made with. Thanks
Click to expand...


I'd strip it completely and have it tanked and inspected first. My local shop does this stuff cheap and does a good job. I'd get a 331 stroker kit for it if you want to run high 11's and have them bore and stoke it. You can get these kits on ebay for cheap. Just my 2 cents...
 
B

bentley429

Banned
Nov 25, 2004
528
3
0
Connecticut
Jul 21, 2006
#11
  • Jul 21, 2006
  • #11
Killer50stang said:
I'd strip it completely and have it tanked and inspected first. My local shop does this stuff cheap and does a good job. I'd get a 331 stroker kit for it if you want to run high 11's and have them bore and stoke it. You can get these kits on ebay for cheap. Just my 2 cents...
Click to expand...

I will be stripping the block and getting it checked out, but Iam not looking to do a stroker kit. The block is a 60k mile 302 out of a 90 GT and still has the stock bore, the cylinders are so fresh you can still see the light scratches.
 
T

TheUser

Active Member
Jul 25, 2003
1,859
1
36
Springfield, MO
Jul 21, 2006
#12
  • Jul 21, 2006
  • #12
If you change the heads, intake and all, you'll probably want another cam since that one is was custom made for a different combo; however, I'm no cam expert, so that one might be fine.

As far as head gaskets, fel pro should be fine if it's tuned properly. You want your head gasket to blow instead of breaking other more expensive things. Your head gaskets should be your weak link. You might consider getting it dyno-tuned after you get it all set up...prob. pick up a few more ponies and some peace of mind.

Good luck.
 
B

bentley429

Banned
Nov 25, 2004
528
3
0
Connecticut
Jul 21, 2006
#13
  • Jul 21, 2006
  • #13
TheUser said:
If you change the heads, intake and all, you'll probably want another cam since that one is was custom made for a different combo; however, I'm no cam expert, so that one might be fine.

As far as head gaskets, fel pro should be fine if it's tuned properly. You want your head gasket to blow instead of breaking other more expensive things. Your head gaskets should be your weak link. You might consider getting it dyno-tuned after you get it all set up...prob. pick up a few more ponies and some peace of mind.

Good luck.
Click to expand...


I was thinking the same thing about the cam, it was used with a set of iron GT40's. Also thinking about the trick flow track heat kit and just selling off my edelbrock intake depending on what everyone suggests to me. The car will be getting a tune regardless.
 

GearHd6

Member
Jul 19, 2005
459
0
18
Ashford, CT
Jul 21, 2006
#14
  • Jul 21, 2006
  • #14
OMG! A response at 3:11pm! GET TO WORK!!!!!!

BAP!
 
B

bentley429

Banned
Nov 25, 2004
528
3
0
Connecticut
Jul 22, 2006
#15
  • Jul 22, 2006
  • #15
GearHd6 said:
OMG! A response at 3:11pm! GET TO WORK!!!!!!

BAP!
Click to expand...


I know!!! The other guy had to leave early so that means me too. BAP BAP!
 

Killer50stang

New Member
May 11, 2004
632
0
0
Jul 22, 2006
#16
  • Jul 22, 2006
  • #16
I'd go with the E303, at least you can run it on stock springs.
 

Rick 91GT

Mustang Master
Nov 29, 1999
9,692
95
99
PA
Jul 24, 2006
#17
  • Jul 24, 2006
  • #17
Fel-Pro 1011-1 would be fine for a good normal performance gasket or if you are going to have it tuned you could go with the Fel-Pro 1133 which are a MLS gasket, just have the surface prepped properly on the block before hand.
 
You must log in or register to reply here.

Similar threads

Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
9
Forced Induction Prepping for supercharger on non-stock build
  • 91fox427
  • Nov 25, 2025
  • Fox 5.0 Mustang Tech
Replies
7
Views
606
Fox 5.0 Mustang Tech Jan 5, 2026
Qtrhrse23
D
First post 289 rebuild question!
  • Ddyer2868
  • Nov 24, 2025
  • Classic Mustang Specific Tech
Replies
3
Views
370
Classic Mustang Specific Tech Dec 5, 2025
rednotch
6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Oct 19, 2026
mattcrp1
M
S
Requesting Guidance for 306 motor swap - Fuel? - SD? MAF?
  • So_Flo
  • Jul 26, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
32
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 4, 2026
Mcmahst
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?