• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

351W questions.

  • Thread starter Thread starter btlfed91
  • Start date Start date Oct 13, 2008
B

btlfed91

New Member
Apr 18, 2008
42
0
0
STL
Oct 13, 2008
#1
  • Oct 13, 2008
  • #1
OK guys im sure some of you have already been here and back already but I'm trying to catch up.I am trying to get together the parts I need to put a 351W in my fox I picked up the longblock already out of a 95 bronco its got everything on it back to the flywheel but I'm not quite sure what I need to do as far as balancing on it with already having everything there.I already read the sticky at the top of the page but I'm still not sure. Can I use the balancer and flywheel that are on the motor now or do I need to get new stuff?I am planning on using my trickflow stuff from my 302,Ive got the oil pan but what about brackets and stuff can I use them off the 351 also?Thanks in advance!
 

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Oct 14, 2008
#2
  • Oct 14, 2008
  • #2
youll need a different lower intake, widen the lines on your 302 rails if you're resuing them, the 351 swap pan or if you can find one from a crown vic it should be the same, not sure about the bronco brackets, the original flywheel and balancer should work as long as the flywheel has the right amount of teeth, also a tfi..efi distributor if it wasn't efi. you'll also need new headers. oh and a spacer for the crank pulley to make it line up to the serpentine setup, assuming you're resuing that. I think thats it....I'm doing the same swap too
 

68stang351

Founding Member
May 16, 2002
850
9
39
Savoy TX
Oct 14, 2008
#3
  • Oct 14, 2008
  • #3
I'm doing this swap right now also. You two pretty much have it covered.

As far as brackets, I'm re-using my fox alternator bracket, because it only bolts to the head, and for the power steering bracket with a/c delete I'm going to going to buy the one from Ford, it's only like 50$. It needs to be replaced because it bolts to the head and also the water pump bolts, which are obviously further away on the 351.
 
You must log in or register to reply here.

Similar threads

N
Vibration after new clutch
  • nipple_looker
  • Sep 20, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
23
Views
709
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 26, 2026
fasterthangas
F
A
Catch can questions.
  • AngryH58
  • Sep 26, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
168
1996 - 2004 SN95 Mustang -General/Talk- Sep 29, 2026
squeak93
Paint and Body Rotten moon roof trim
  • Teen'93stang5.0
  • Apr 14, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
227
Fox 5.0 Mustang Tech Apr 15, 2026
Teen'93stang5.0
W
Front ATS brakes with Taurus rear brakes. Full parts needed?
  • Wagonized
  • Sep 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
291
Fox 5.0 Mustang Tech Sep 25, 2026
General karthief
Electrical Code 29 again
  • Creomod
  • Jul 31, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
387
Fox 5.0 Mustang Tech Aug 3, 2026
Creomod
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?