4.6 in a 86-93

joeyd0730 · May 22, 2005

i am looking for any information that will let me know if it is possible to put a 32v 4.6 in a 87-93 mustang. can this be done without extensive fabrication? in anyone can point me in the right direction i would appreciate it, thans in advance, joe

86T-Top · May 22, 2005

Sure it can be done. Get a k-member from 32V 4.6L mustang, wiring harness and computer. Also you will need the tranny and x-member that go with that trans. Finally you will need the headers and h-pipe that go with that car.

The easiest way to do it; find a wrecked cobra with all those parts and swap em out.

Mario

Daggar · May 22, 2005

MM has a cross member now that will allow you to put a mod in a Fox. An 03/04 Cobra motor would be sweeet!

Big $$$ though.

Thenemesis · May 22, 2005

but whats the point when a 5.0 is better lol

Daggar · May 22, 2005

Thenemesis said:
but whats the point when a 5.0 is better lol

You're silly.

An intercooled Kenne Bell on a Cobra 4.6 in a Fox body???? That'd be sick! LOL

Wouldn't be worth doing unless you could get it all underneath of the hood IMO though.

Thenemesis · May 22, 2005

lol yea... a kenne bell blower stickin out the hood that was ghetto cut to make it shut wouldnt be to sleeper would it id like the idea of a factory cobra motor tho

1990Coupe · Jun 10, 2005

86T-Top said:
Sure it can be done. Get a k-member from 32V 4.6L mustang, wiring harness and computer. Also you will need the tranny and x-member that go with that trans. Finally you will need the headers and h-pipe that go with that car.

The easiest way to do it; find a wrecked cobra with all those parts and swap em out.

Mario

OK well what if your debating putting just the stock 4.6l outa an 01gt into a fox, all i would need is the k member, and all the exhaust stuff? The tranny will be a 5-speed so im assuming all id need is the bellhousing, the tranny should be fine. What about the driveshaft length? also with the computer harness, would that mean id have to change ALL the harnesses in the car? or could i just get the computer harness and plug it into the dash harness already in the car?? im curious because my car is in paint right now, and its just about done. Im going to Sell it as soon as it comes outa paint cause i need the money right now to settle some depts. Once thats settled i plan on buying like an 87-93 4 banger and swap her over. I figure the 4.6 route would be pretty sweet?

1990Coupe · Jun 10, 2005

Im guessin nobody knows what is needed????

1990Coupe · Jun 10, 2005

Nevermind i found some stuff.. almost seems not worth it to me.. im just gunna swap to a 5.0 and just do that up..

ms93gt · Jun 10, 2005

The amount of money it would cost to do the swap you could build a better motor such as a stroker and it would kick the cobra's ass.

1990Coupe · Jun 10, 2005

yea thats what im gunna do.... my dream of being different is gone..

ms93gt · Jun 10, 2005

1986Stang said:
yea thats what im gunna do.... my dream of being different is gone..

Were you out on 37 last Saturday or Friday?

machfelon · Jun 10, 2005

stang22 · Jun 10, 2005

You could put the Cammer in? It's only $15,000.00.

http://secure.50resto.com/product1.cfm?SID=1&Product_ID=2883

4.6 in a 86-93

joeyd0730

Member

86T-Top

Daggar

New Member

Thenemesis

Member

Daggar

New Member

Thenemesis

Member

1990Coupe

1990Coupe

1990Coupe

ms93gt

New Member

1990Coupe

ms93gt

New Member

machfelon

New Member

stang22

Active Member

Similar threads

4.6 in a 86-93

Member

New Member

Member

New Member

Member

New Member

New Member

New Member

Active Member

Similar threads

Privacy & Transparency

Privacy & Transparency