5.0 problem

S

sshakrr

New Member

Jul 12, 2005

4

0

0

Jul 12, 2005

#1

• Jul 12, 2005

• #1

Hello, Im new to the site and have a question about my 1988 5.0 LX. Ive given it a tune up including cap, rotor, plugs, wires, gas filter, and oxygen sensors. Ive had it in at my local ford dealer and ran the diagnostic test twice. First time he said the plugs were the problem ( autolites) so I put in motorcrafts and still the engine stumbles when you get on it even a little. The car has almost 43k miles on it. Im lost as to what it could be and so was my dealer! Has anybody expierenced this type of issue and what did you do to remedy the situation? Any help would be appreciated Thanks Ron

 

Legendary

Founding Member

Oct 10, 2002

1,925

0

0

City of Angels

Jul 12, 2005

#2

• Jul 12, 2005

• #2

On two separate occassions one car had a bad MAF connection that caused it to stumble and the other had bad Cats. Just a guess.

 

Paul Perreca

New Member

Mar 30, 2005

1,085

0

0

Jul 12, 2005

#3

• Jul 12, 2005

• #3

i would say check for a vaccuum leak, but you'd probably feel that at idle, but i dont know if there is one that would affect full throttle -

 

whtpny

New Member

Dec 8, 2002

338

0

0

Spokane WA.

Jul 12, 2005

#4

• Jul 12, 2005

• #4

From something I read on here the other day I would check the coil. Could be bad and wil not work well under load at all. Check all electrical connections. Clean the MAF. I cannot believe the Ford dealer did not find it.(or should I)

 

HISSIN50

"How long does it take to get help in here?

15 Year Member

Nov 29, 1999

31,179

34

129

Jul 12, 2005

#5

• Jul 12, 2005

• #5

Welcome to the boards!

Based upon what you said (there were no codes? Did they use a scope?), I would check basic things.

Be sure the plug wires are not touching anywhere (I know they are new, but are they touching?).
Check your TPS for a smooth run from ~1 volt to ~4.5 volts. Be sure there are no breaks in the volts as you open the TPS (dead spot). Stuff like that. Good luck.

 

Daniel50

New Member

Mar 30, 2005

716

1

0

Discovery Bay, CA

Jul 12, 2005

#6

• Jul 12, 2005

• #6

Legendary said:

On two separate occassions one car had a bad MAF connection that caused it to stumble and the other had bad Cats. Just a guess.

Click to expand...

car is an 88 so no maf

 

P

proxses

Founding Member

Dec 12, 2000

620

0

0

Dayton, Oh

Jul 13, 2005

#7

• Jul 13, 2005

• #7

'88 California cars came with a MAF.
I'd look into fuel pressure as well. It may be able to let the car idle, but under load you may be seeing fuel starvation. The filter was changed, but the pump may be worn out.
Also check the MAP sensor and see if it is unplugged, or maybe has a damaged wire.
Also, it would be nice to know if the car is SD or mass air.

And what is the plug gap set at?

 

89CopCoupe

Banned

Feb 17, 2004

606

0

0

Post Count City

Jul 13, 2005

#8

• Jul 13, 2005

• #8

What the hell dealer can't figure out why the car is stumbling

Did you pay And if so Go back and demand results.

If the sensors are functioning properly and consequently the air/fuel is dead on in all areas, the only place left is ignition.

Dealers are at a loss with speed density cars now Another nail in the coffin of America

 

S

sshakrr

New Member

Jul 12, 2005

4

0

0

Jul 13, 2005

#9

• Jul 13, 2005

• #9

Thanks for the great advise! I have SD and the plugs are gapped at .054 (.052-.056) is whats on the emission label. I was thinking maybe a vac. leak or coil going bad or clogged injectors or bad fuel pressure. But those were just guesses and will look into them this weekend. Again thanks for the support Ron