• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

5 lug wheel problem

  • Thread starter Thread starter Vapors
  • Start date Start date Oct 26, 2005

Vapors

New Member
Aug 26, 2005
39
0
0
Bakersfield
Oct 26, 2005
#1
  • Oct 26, 2005
  • #1
I need to get a new set of wheels really bad, but I'm not sure which ones to get.

The problem is its been converted to a 5 lug(on an 87 LX Coupe) if I'm reading correctly, their are different ways to convert from 4 lug. If if was converted over by means of SN95 parts, will I order wheels that will fit 94+ cars? And is their a way to tell how they converted it? It still has drums in the back btw.

EDIT: Another thing to add, when my problem first came about, I went and had the wheel bearings checked and repacked, would they not be able to do that if it was an sn95 conversion?

crapola
 

Shakerhood

20+ Year Stangneter
Oct 28, 2004
3,361
211
114
Ohio
Oct 26, 2005
#2
  • Oct 26, 2005
  • #2
If you have a sealed bearing hub up front you have an SN95 Conversion and then will have the biggest choice of wheels. Bullitts look really nice on a Fox!
 

Vapors

New Member
Aug 26, 2005
39
0
0
Bakersfield
Oct 26, 2005
#3
  • Oct 26, 2005
  • #3
What I was getting at was after I find out what conversion I have, how do I look for wheels? ie..should I order wheels like my car is a 94+ if it has the sn95 conversion? Or if it the other way, do I order wheels for an 87 like my car is?

???
 

tunedin302

I AM the law!!!
Jul 29, 2004
1,251
2
36
Pennsylvania
Oct 26, 2005
#4
  • Oct 26, 2005
  • #4
Vapors said:
What I was getting at was after I find out what conversion I have, how do I look for wheels? ie..should I order wheels like my car is a 94+ if it has the sn95 conversion? Or if it the other way, do I order wheels for an 87 like my car is?

???
Click to expand...

You will want 94+ wheels for your car. The problem you may encounter is with the centercap and mounting. If you have sn95 spindles then you would be able to take only the rotor off and the studs would remain on the spindle. Here's a pic of what I mean:

View attachment 499469

However, if it was a lincoln conversion then the rotor will have the studs in it and look like this:

View attachment 499471

If you have lincoln rotors (lower picture) then it will limit your selection in wheels for two reasons. First, you may not be able to run the centercap on the front wheels. This is because the dust cap on the rotor will pertrude through the centercap area. You can either push down the dust cap or not run one (don't do if daily driven) so the centercap will fit. Secondly, depending on which wheel you get, you may have to grind the end of the rotor so the wheel will sit flush. Check out this thread for more info on the lincoln setup:
http://www.corral.net/forums/showthread.php?t=671052&highlight=saleen
 
2

2002BLGT

Well-Known Member
Dec 18, 2003
2,945
4
59
Bedford VA
Oct 26, 2005
#5
  • Oct 26, 2005
  • #5
even if you use the lincoln rotors to convert , you just need 7/16th wheel spacers and longer studs to make the newer wheels work .....
 

Vapors

New Member
Aug 26, 2005
39
0
0
Bakersfield
Oct 26, 2005
#6
  • Oct 26, 2005
  • #6
Well I think it might be the lincoln rotors, not entirely sure. But the Cobra Rs I do have on the car have center caps if thats relevent.

And so if it is the lincoln rotors, to get the 94+ wheels to work I would need to run a spacer?
 

tunedin302

I AM the law!!!
Jul 29, 2004
1,251
2
36
Pennsylvania
Oct 27, 2005
#7
  • Oct 27, 2005
  • #7
Vapors said:
Well I think

And so if it is the lincoln rotors, to get the 94+ wheels to work I would need to run a spacer?
Click to expand...

Depends on which wheel you go with. I don't agree with the above post above the spacer. Again, depending on the wheel, you could take off the dust cap and not run a spacer. You will have to experiment with it. Good luck.
 

Shakerhood

20+ Year Stangneter
Oct 28, 2004
3,361
211
114
Ohio
Oct 28, 2005
#8
  • Oct 28, 2005
  • #8
It would probably be easier for you to convert the fronts to SN95 Specs.
 
T

tjm73

Founding Member
Aug 3, 2000
2,418
2
48
Rush, NY
Oct 28, 2005
#9
  • Oct 28, 2005
  • #9
Their is a new option. '05-up wheels with a 1" H&R or Eibach spacer. Just something to consider.
 

FORCED2DV8

New Member
Jun 6, 2005
458
0
0
Grand Rapids MI
Oct 28, 2005
#10
  • Oct 28, 2005
  • #10
Pull a wheel off and see what conversionyou have, that way it will illiminate alot of guessing, Also there is so many different back spacing and wheel options you will have to try them out or go measure.
 

CoupedUp

Banned
Aug 26, 2005
260
0
0
Gone Fishing
Oct 28, 2005
#11
  • Oct 28, 2005
  • #11
Wheel Offsets For 5-lug Foxers

Lincoln/Ranger 5-lug conversion
8" wide wheel:
Front: +12mm
Rear: 0mm

9" wide:
F: +30mm
R: +18mm

SN 5-lug conversion
8" wide:
F: +18mm
R: +18mm

9" wide:
F: +36mm
R: +36mm
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Oct 28, 2005
#12
  • Oct 28, 2005
  • #12
What wheels do you want to run??
 
T

tjm73

Founding Member
Aug 3, 2000
2,418
2
48
Rush, NY
Oct 28, 2005
#13
  • Oct 28, 2005
  • #13
CoupedUp said:
Lincoln/Ranger 5-lug conversion
8" wide wheel:
Front: +12mm
Rear: 0mm

9" wide:
F: +30mm
R: +18mm

SN 5-lug conversion
8" wide:
F: +18mm
R: +18mm

9" wide:
F: +36mm
R: +36mm
Click to expand...

Screw this offset crap. Offset means nothing to me. yeah I understadn it, but it's worthless by it's self. You have to convert it over to SAE and figure out backspace for it to be of any value IMO.

To do that divide the offset by 25.4. That's the SAE measurement. Now add 1" to the wheel width and then divide that by 2. Add that to the converted offset and that's the approximate backspace you need.
 

CoupedUp

Banned
Aug 26, 2005
260
0
0
Gone Fishing
Oct 28, 2005
#14
  • Oct 28, 2005
  • #14
tjm73 said:
Screw this offset crap. Offset means nothing to me. yeah I understadn it, but it's worthless by it's self. You have to convert it over to SAE and figure out backspace for it to be of any value IMO.

To do that divide the offset by 25.4. That's the SAE measurement. Now add 1" to the wheel width and then divide that by 2. Add that to the converted offset and that's the approximate backspace you need.
Click to expand...

Do the math for me then. I like offset .... it makes me feel global
 
T

tjm73

Founding Member
Aug 3, 2000
2,418
2
48
Rush, NY
Oct 28, 2005
#15
  • Oct 28, 2005
  • #15
CoupedUp said:
Do the math for me then. I like offset .... it makes me feel global
Click to expand...

It's not as simple as this or that offset will work or not. You have to evaluate each wheels fitment seperately.
 

CoupedUp

Banned
Aug 26, 2005
260
0
0
Gone Fishing
Oct 28, 2005
#16
  • Oct 28, 2005
  • #16
tjm73 said:
It's not as simple as this or that offset will work or not. You have to evaluate each wheels fitment seperately.
Click to expand...

I agree that not all wheels fit exactly the same ... but if the wheels are manufactured properly and have an exact backspacing, then a fitment guideline can be resolved.

From an offset perspective ... as long as the bizarre manufacturers are thrown out of the equation (any ones that would make a wheel with an oversized bead-lip) the chart I posted above will house any given wheel nicely relative to the fenders and the chassis interference parts (a-arms, struts, etc)

Of course fitment factors such as coil-over suspensions and hub mounting surfaces play a role.
 

Vapors

New Member
Aug 26, 2005
39
0
0
Bakersfield
Nov 15, 2005
#17
  • Nov 15, 2005
  • #17
Mustang5L5 said:
What wheels do you want to run??
Click to expand...

I have the lincoln rotors btw.

The ones I was looking at are the ones like I have now, but I want 8" instead of 9"

Specifically the AFS White Cobra R style. 17x8 (5-Lug) 12mm offset with 4.95 BS Are those the wheels I need? On the website, they are for a 94+
http://www.afswheels.com/v2/ecommerce/shopexd.asp?id=115
 

Vapors

New Member
Aug 26, 2005
39
0
0
Bakersfield
Nov 16, 2005
#18
  • Nov 16, 2005
  • #18
Ttt

:d
 
You must log in or register to reply here.

Similar threads

Rear Disc and Rims Offsets
  • TripleYellow
  • Nov 11, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
19
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jan 9, 2026
TripleYellow
Progress Thread 91GTstroked 90 7 up convertible build
  • 91GTstroked
  • Apr 18, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
478
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 22, 2026
91GTstroked
Cobra Brake Conversion - Spare Wheel/Tire Search
  • AeroCoupe
  • Aug 2, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
510
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 2, 2026
AeroCoupe
P
Wheels-Tires 04 Mustang Wheels won't sit against rotor
  • pindude80
  • Jun 10, 2024
  • Fox 5.0 Mustang Tech
  • 3 4 5
Replies
86
Views
6K
Fox 5.0 Mustang Tech Apr 28, 2025
pindude80
P
G
Intro and FB questions
  • gflat65
  • Nov 16, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
1
Views
295
1965 - 1973 Classic Mustangs -General/Talk- Nov 25, 2025
horse sence
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?