'70 Fuel tank in my '66

golf4283 · Mar 20, 2009

Ok I know there have been other threads on this subject but I'm wondering if anyone knows how high a 1970 fuel tank rises above the mounting point?

I ask because I want to drop one in my '66 and want to make sure it either sits flush or below the rest of the trunk area because I plan to make a "floor" with some plywood and a bit of carpet attached to it. I want to do this to give the trunk a bit more of a finished look.

So if anyone has a measurement or can tell me from experience that would be great. either that or the 69 tank I believe is 20 gallons so it's most likely shorter and will fit.

Thanks
-Dan

SNAKEPILOT · Mar 20, 2009

It's 2 1/2" from the top of the tank flange. A '69 tank is lower but the filler opening is more to the rear which makes hooking up the tank much more difficult.

12sec67 · Mar 20, 2009

The angle of the filler tube needs to be changed

golf4283 · Mar 20, 2009

that's not the problem. I'm more so just curious as to which one mounts flush with the rest of the trunk for the purposes of building a flat trunk floor with no dip at the gas tank.

CraigMBA · Mar 20, 2009

golf4283 said:
that's not the problem. I'm more so just curious as to which one mounts flush with the rest of the trunk for the purposes of building a flat trunk floor with no dip at the gas tank.

That depends on what your definition of 'flat' is. The trunk floor is tapered from the rear end (where the floor is higher than the tank) to the taillight panel (where the tank is higher than the floor.

Here are pictures of my '70 tank in my '65:

That #1 phillips screwdriver will almost slide under the straight edge.

It's almost flat here, but I wouldn't call it flat.

When I had an IASCA competition stereo system in the late 1980's, I had installed a flat floor. The tank wouldn't of interefered with me doing it again, but that's a long way off right now.

golf4283 · Mar 20, 2009

now what did you do for the filler neck on that tank in your '66? Did you modify your existing filler neck or purchase the '70 neck?

CraigMBA · Mar 20, 2009

I cut it down the stock neck the exact amount the tank was higher. It doesnt line up perfect, but it's close. I'm understand I can re-align the neck with two jack handles but I haven't done it yet.

66 Restomod · Mar 21, 2009

Here's a pic of my 22 gallon tank in my 66:

undercoated but uncarpeted trunk pic

I used a 4x8 sheet of eucaboard and 3.5 yards of Ford Blue carpet and ended up with this as a finished product:

Restoration and Modification of a 1966 Mustang "Restomod": Junk in the Trunk: The Finale

rbohm · Mar 21, 2009

66 Restomod said:
Here's a pic of my 22 gallon tank in my 66:

undercoated but uncarpeted trunk pic

I used a 4x8 sheet of eucaboard and 3.5 yards of Ford Blue carpet and ended up with this as a finished product:

Restoration and Modification of a 1966 Mustang "Restomod": Junk in the Trunk: The Finale

nice job finishing the trunk

stonecoldtx · Mar 21, 2009

66 Restomod said:
Here's a pic of my 22 gallon tank in my 66:

undercoated but uncarpeted trunk pic

I used a 4x8 sheet of eucaboard and 3.5 yards of Ford Blue carpet and ended up with this as a finished product:

Restoration and Modification of a 1966 Mustang "Restomod": Junk in the Trunk: The Finale

That's a great looking trunk! What thickness board did you use? What did you do for support under the board?

66 Restomod · Mar 22, 2009

stonecoldtx said:
That's a great looking trunk! What thickness board did you use? What did you do for support under the board?

Thanks guys! The eucaboard board is pretty thin but strong, I believe 3/16". This was the only thickness they had at Home Depot and worked fine for my needs. I used it to create a backer board to put the carpet vertical behind the rear seats. I also used it to put down a floor for the trunk it 2 pieces, and a third long piece before the rear seats. With the big tank, there's good support, except for the area closest to the forward area of the fuel tank. (I used a 12" or so block of wood, glued to the top of the fuel tank to support the eucaboard.) Then I used it the create 2 slanted panels for attaching to the rear taillight area. It's strong for it's size, and water resistant too. The shiny side is the best side for glue I found.

'70 Fuel tank in my '66

golf4283

Active Member

SNAKEPILOT

New Member

12sec67

Active Member

golf4283

Active Member

CraigMBA

New Member

golf4283

Active Member

CraigMBA

New Member

66 Restomod

Member

rbohm

stonecoldtx

Member

66 Restomod

Member

Similar threads

'70 Fuel tank in my '66

Active Member

New Member

Active Member

Active Member

New Member

Active Member

New Member

Member

Member

Member

Similar threads

Privacy & Transparency

Privacy & Transparency