Progress Thread 83 Gt Getting Street Worthy

83-gt-hatch · Jun 15, 2015

I sanded the rust off the dipstick. Hopefully I can change the oil and start adjusting the dipstick to length tomorrow. At least I can tinker with that until this weekend.. Put the new spark plug wires on as well... Out of curiosity anytime here have pics of how you run your wires to make it look less clustered

83-gt-hatch · Jun 20, 2015

Got a little update for y'all... Finally got the bolt out by the heat of the motor and an Allen key and some luck. Had to cut the new bolt down to size to get it to fit. It did have a thermostat in there but was flowing on a cold motor so no good. Was a 160 anyways. Put a new 180 in and a reman water pump. Havnt filled it with antifreeze yet. No rush going to test run in tomorrow's 90 something degree weather rather then in a light sprinkle at night.... If I could get a video to upload if show y'all how it's running now. I it to thinking and a friend reminded me about fuel pressure and with a quick gauge install I found I wasn't getting enough fuel to run it. New pump and 2 new filters later it's running great.. I do plan to clean the carb and new gaskets in the near future just since it has sat and if there could be any dirt in there. Precautionary measure

83-gt-hatch · Jun 20, 2015

I will get some pics of the shiny new water pump and bolts along with the shiny new fuel psi gaugeunder the good with the filter bbehind it with some better looking gas in there as opposed to that orange crap that I got a couple weeks ago

stang89bidges · Jun 20, 2015

Glad to hear the bolt came out with ease. A little luck can make a big difference sometimes. Good job checking fuel pressure. Back in business.

83-gt-hatch · Jun 20, 2015

You and me both lol. I'm much happier to have a new thermostat in there. Hope that fixes the overheating. Will find out tomorrow.. I have a gauge in the back that read 5 but no way to Rev it and look. Put a block of wood on the floor holding 2k rpms and it was at 2 or less psi right at the pump. 500rpm it showed 3 and a half. 250 rpm it read 4. Put a gauge up by the carb and similar results just less. Pump was to weak. That's when I started remembering the pump used to be really loud and wasn't now. My my awesome Mr .Gasket high performance electric universal fuel pump got it going again lol. Not performance really

stang89bidges · Jun 20, 2015

Dude, you should be able to push/pull the throttle body from the engine bay yes?

83-gt-hatch · Jun 20, 2015

It's carbureted but if I had one I could. I've had just about everything else out by now lol

stang89bidges · Jun 20, 2015

Carbs have throttle body's too, just pull the lever that the throttle cable hooks too. Might have to take off the air cleaner.

83-gt-hatch · Jun 20, 2015

I did not know that... Out leaks a little. Need a new thermostat housing. Try to find one tomorrow

83-gt-hatch · Jun 21, 2015

stang89bidges said:
Carbs have throttle body's too, just pull the lever that the throttle cable hooks too. Might have to take off the air cleaner.

Sorry. I must have been out if it last night. I know what your talking about. Yes I can Rev it from the carburetor. At the time the only gauge was in the rear wheel well area

stang89bidges · Jun 21, 2015

Ah, I see, I didn't catch that. Lol that makes more sense.

83-gt-hatch · Jun 21, 2015

Today's update. New thermostat housing came with a poorly cut gasket. Got some gasket material and cut my own out and no more leaks from there. Water pump was leaking so pulled it off and put some rtv on it and that leak stopped then once I got that back on I found the heater hose sprung a leak fixed that. No more leaks at the moment. It's starting near normal then rising up almost in the overheating stage but not quite. Then it week drop back down then back up. Gonna try to get it to work then a buddies shop to get it looked at. See what they think about it

stang89bidges · Jun 21, 2015

That sucks. Hopefully it's cooling system and not heads or worse.

83-gt-hatch · Jun 21, 2015

Lol. Finally I found a block of wood to set against the pedal.. Now I have a easy to see gauge right next to the carb to rev it from there if need be to check outside of idle what I'm getting

83-gt-hatch · Jun 21, 2015

I just did a compression test last week since it got hotter then it should've. Highest was 165 on cyl 6. And cyl 3. Lowest was 153 on first attempt and 159 on 2nd attempt on cyl 1

83-gt-hatch · Jun 21, 2015

Radiator is probably the one Ford put in in 83. So probly time

83-gt-hatch · Jun 21, 2015

Some pics from today

83-gt-hatch · Jun 21, 2015

Now my passenger side window won't budge. It's getting power. I hear it's draw from switches anda click from for ppanel

83-gt-hatch · Jun 21, 2015

Got it up. Somehow I wiggled the door switch on the passenger side and down then up it worked.. Just something else to do lol

90sickfox · Jun 21, 2015

Good to see things are coming a long.

Progress Thread 83 Gt Getting Street Worthy

Member

Attachments

Member

Attachments

Member

Attachments

Advanced Member

Member

Advanced Member

Member

Advanced Member

Member

Member

Advanced Member

Member

Advanced Member

Member

Member

Member

Member

Attachments

Member

Member

Wasn't a pretty sight...and I've got big hands

Similar threads

Privacy & Transparency

Privacy & Transparency