95GT driveline into '83

fiveohlxhatch

New Member

Sep 18, 2007

27

0

0

Dec 17, 2007

#1

• Dec 17, 2007

• #1

Found a great deal on a wrecked '95GT that i'll be using the suspension from to do a 5 lug conversion on my brother's 83 Mustang for. The driveline was supposed to be already sold but when I showed up I was able to strike a deal on it as well. I know the SN95 trans has a different length input shaft as well as bellhousing from a Fox 5.0 but I have all the parts from this SN95 car. My question is what driveshaft do I use? I had already bought a 5spd conversion from a donor '87 GT including the bell/trans/flywheel/driveshaft. Any ideas on which would be better to use? We were planning an A9L EFI conversion for the car so most of the engine pieces will be used already. Just looking for input on the trans issue.

 

BlownFiveLiter

have car, will race....wait, it doesn't run

15 Year Member

Nov 29, 1999

3,133

18

108

Chicagoland

Dec 17, 2007

#2

• Dec 17, 2007

• #2

If I were in your shoes, I'd use the Fox trans, bellhousing, and driveshaft. There's a lot more of those around if you need a new one, versus only two model years' worth of parts for the 94-95's. Otherwise, it should all be a pretty straightforward swap, and sounds like a fun project. Good luck!

 

jrichker

StangNet's favorite TOOL

In Remembrance. Thank you for your contributions

Mar 10, 2000

27,512

2,813

234

Dublin GA

Dec 17, 2007

#3

• Dec 17, 2007

• #3

Your brakes are going to need some interesting modifications to work properly. See http://www.svo73mm.cjb.net/ for budget brake upgrades & 5 lug swaps. One of the best sites around for Mustang brake help.

 

NKau

Founding Member

Dec 15, 2001

1,346

0

37

Jefferson, WI

Dec 17, 2007

#4

• Dec 17, 2007

• #4

I think the sn-95 t-5's have a different shifter location too, but don't quote me on that. I'd see if I could sell that t-5 and just get one from a fox.

 

BlownFiveLiter

have car, will race....wait, it doesn't run

15 Year Member

Nov 29, 1999

3,133

18

108

Chicagoland

Dec 17, 2007

#5

• Dec 17, 2007

• #5

The SN95 shifter is in the same location on the case, but because of the 5/8" longer input shaft, the shifter will be moved back in the same distance inside the car.

 

SVT32VDOHC

waiting for the next hack atta

Founding Member

Nov 22, 2001

3,501

28

119

Motor City

Dec 18, 2007

#6

• Dec 18, 2007

• #6

Yeah, you might have to notch the floor a little. No big deal. Tin snips or an air grinder will do. The 5 lug swap and brake swap was the best updgrade I did to my 91. I love it, people love it.

 

fiveohlxhatch

New Member

Sep 18, 2007

27

0

0

Dec 19, 2007

#7

• Dec 19, 2007

• #7

Thanks for everybodys comments. Based on what everybodys saying i'll use the fox t-5 swap instead. StangGT1995 you brought up a really good point about availability in case I need to find a t-5 down the road. Jrichker thanks for the link. I've been reading his site as well as others on the 5-lug swap so I knew what I was diving into before I got in over my head. SVT32VDOHC Your '91 notch looks sick with the '96 Cobra rims. You just don't see those around! Can't wait to see your '81 in the next few stages. Thanks again everybody for your input.