• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

allignment issues chewing up tires.

  • Thread starter Thread starter dp88
  • Start date Start date Dec 31, 2008

dp88

New Member
Oct 30, 2008
40
0
0
Dec 31, 2008
#1
  • Dec 31, 2008
  • #1
I have had an ongoing allignment issue due to what i can olnly guess is the lack of c/c plates after lowering. I recently installed a set of the ford racing lowering springs and have since noticed the top of the tire is angled in to the engine bay on both sides but more angled on the drivers side. The inside of both tires are wearing prematurely but again the driverside more. The car does want to pull to the right as well. I have replaced the ball joints already and would appreciate some input on if you think it is time to get c/c plates, and if it is common for one side to be out of wack more than the other. Tkanks for your help.
 

Attachments

  • 015.webp
    104.9 KB · Views: 191

squeak93

15 Year Member
Jun 2, 2005
2,351
417
164
Joplin, Missouri
Dec 31, 2008
#2
  • Dec 31, 2008
  • #2
cc plates are the easiest way to fix it. Cheaper than new front tires too.....
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
Dec 31, 2008
#3
  • Dec 31, 2008
  • #3
Yes, the cc plates are the best way to correct this. You could try enlarging the upper strut mounting holes but the plates will almost certainly allow a good alignment.

After I installed the Ford lowering springs, a shop aligned it, and showed me the printouts indicating that they could still get it within the factory specs. That actually allows quite a bit of variation from optimum. But it still pulled to one side noticeably, and they were out of adjustment to correct it.

So I got the plates. Because the first shop was closed when I got the plates on, I went to a much smaller shop where the owner worked on antiques and rods and such. He set it up nicely so that it drove straight, did not wear tires, etc, and has been doing all of my alignment since 92.
 

dp88

New Member
Oct 30, 2008
40
0
0
Jan 1, 2009
#4
  • Jan 1, 2009
  • #4
Can someone point me in the right direction of some good c/c plates. Im not sure which ones i should get because i have to keep the stock hood. Thanks
 
You must log in or register to reply here.

Similar threads

B
Where to go from here on my build…
  • B0udreaux
  • Jul 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
458
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 18, 2026
AeroCoupe
J
Severe shaking/vibrations in steering wheel
  • jacket999
  • May 20, 2025
  • SN95 V6 Mustang Tech
Replies
8
Views
1K
SN95 V6 Mustang Tech Jun 1, 2025
NtheGAME
N
S
Drivetrain 8.8 Pinion and 302 rear main seal leaks after replacing. 93 5.0 with t-5
  • Steigy4827
  • Jun 23, 2025
  • Fox 5.0 Mustang Tech
Replies
10
Views
879
Fox 5.0 Mustang Tech Apr 1, 2026
Steigy4827
S
Progress Thread 87 T-top slow progress
  • wobbyguy
  • Feb 2, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 10, 2025
nickyb
Place to Avoid: Jamison Auto Group in Gulfport, MS
  • D Durden
  • Oct 20, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • 2 3
Replies
46
Views
4K
1965 - 1973 Classic Mustangs -General/Talk- Jul 16, 2026
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?