Another how fast will i go.....please guess

92importkiller

Member

Feb 25, 2006

43

0

6

Feb 28, 2006

#1

• Feb 28, 2006

• #1

ok guys, my motor blew up in my car and i am building a new one, how fast do you think it will go in the 1/4 as long as the driveline holds together N/A and on the juice??? Also horsepower guesses..... are 10's possible 400-425 horse N/A

DSS level 20 block
306
Main girdle with ARP studs
Eagle 4340 forged 3.00 inch crank
Eagle 4340 forged H beam rods
Mahle .030" Forged pistons
Lunati .560/.576 lift .300/.310 duration cam
Harland Sharp roller rockers
Edelbrock Victor Jr. Heads
Edelbrock Victor EFI intake
Edelbrock water pump
Edelbrock Cold air kit
BBK 75mm throttle body and spacer
24lb injectors
Underdrive Pulleys
Electric fan
MSD pro billet distributer
MSD 8.5mm Wires
MSD 6al Ignition
MSD rpm activate window switch
Edelbrock nitrous Kit 175shot
3.73 gears
Spec stage 3 clutch
Pete Jackson noisey gear drive
clevite 77 bearings

I think that's it....

 

T

tony91723

Member

Nov 30, 2004

71

0

7

Feb 28, 2006

#2

• Feb 28, 2006

• #2

400hp N/A? I dunno On my 347 that is being built I am hoping for those kinds of numbers. I hope you are running some serious compression and are revving the piss out of it.

 

92importkiller

Member

Feb 25, 2006

43

0

6

Feb 28, 2006

#3

• Feb 28, 2006

• #3

i plan on spinning it to 7500 and 10:1 compression........and i mean 400 at the motor not the wheels.

 

aleborjas

New Member

Sep 11, 2005

610

0

0

Mar 1, 2006

#4

• Mar 1, 2006

• #4

you should be arround 400HP's i think you need a little more fuel like 30 pounders...

 

ram360

Founding Member

Oct 19, 2002

2,162

1

59

Pennsylvania

Mar 1, 2006

#5

• Mar 1, 2006

• #5

I also think your injectors are kinda small.

 

92importkiller

Member

Feb 25, 2006

43

0

6

Mar 1, 2006

#6

• Mar 1, 2006

• #6

ok how about some 42lb injectors anybody else have any ideas of horsepower numbers and 1/4 times

 

7-UP BILL

Founding Member

Jan 4, 2001

885

19

49

My other car is a Firetruck

Mar 1, 2006

#7

• Mar 1, 2006

• #7

42lb injectors are way too big for that motor. I'm supercharged w/about 450 streetable hp and i run 36's. Do a search and find the formula to properly calculate what size injectors are correct for you. It's been awhile, I can't remember it.

 

$uperstang

New Member

Jul 20, 2004

476

1

0

Detroit, MI

Mar 2, 2006

#8

• Mar 2, 2006

• #8

24lb injectors are plenty!!! HP 350 fwhp N/A

 

8

86bluecobra

Advanced Member

Dec 20, 2004

4,265

12

69

B.C. Canada

Mar 3, 2006

#9

• Mar 3, 2006

• #9

from what i have read you need in the nieghborhood of 450 rear wheel hp to dip a fox into tens.

 

R

Redrooster

New Member

Jul 13, 2005

73

0

0

Mar 3, 2006

#10

• Mar 3, 2006

• #10

Just wondering.... why are you going to spend the money on a forged short block and stop at a 306? If you are going to drop the money for a forged rotating assembly why not go with a 331 or 347? I think your combo would run better that way. I also think you have too much duration on you cam for a 306 unless its a track only car. You did not say what the LSA of the cam is, but I would guess low 11's on the motor with say 4.56 gears turning it to 7500 or so.
depends on the weight of the car and suspension/tires.

 

TC93

Well-Known Member

Sep 11, 2000

2,075

1

57

Ellerslie GA 31807

Mar 3, 2006

#11

• Mar 3, 2006

• #11

I think with the 306 combo you should get the 400hp mark in the RPM you are wanting. Bit I have to agree with Redrooster, why not go with a 331 or 347 with the same compression and have the torque to get you moving and then let the HP run the numbers you want.

Remember though, it's not all about HP to run good numbers, suspension has allot to do with with it also. I would say with a 331/347 with your combo above and decent suspension(traction ), you should be able to put out some decent times.

 

I

IntenseBlue

Member

Jul 10, 2005

946

0

16

Mar 3, 2006

#12

• Mar 3, 2006

• #12

I'd get 30/36s. 24s ARE too small for a 7500rpm engine with a Vic. JR head/intake. You're gonna need some 4.10/4.30s for that, too. Low-end is going to suck balls. Hope it's track only.

 

69Rcode_Mach1

Active Member

Apr 20, 2004

1,473

1

37

Salt Lake City, Utah

Mar 3, 2006

#13

• Mar 3, 2006

• #13

That cam and heads is too big unless you stroke it. Even with my 351w bored .040 it will be going to 7000-7500 to get good numbers. I highly recommend stroking it. Look at my sig I am running that exact same cam with a set of FRPP 1.7 rockers.