anybody have their stock lower control arms 99-04 MATCH UP

dastang2

Active Member

Dec 11, 2003

2,020

0

46

tx

Jan 23, 2007

#1

• Jan 23, 2007

• #1

i have a set of bbk lower control arms for a fox but not sure if they fit a 99-04. some people say yes and in magazines some ads say 79-04. i mic'd the metal sleeve for the bushings and this is what i got. length. 2.898" inside diameter is .469. the reason i did this is because i was told that the only difference was the bolts that go through the sleeves. can somebody measure their stock 99-04 sleeves or even aftermarket ones that are not installed yet.

 

J&M Products

Premium Sponsor

Jan 22, 2007

62

10

29

Paso Robles

Jan 23, 2007

#2

• Jan 23, 2007

• #2

The difference between the 79-98 arms and the 99-04 arms is the bolt diameter, the 79-98 use a 12mm bolt and the 99-04 cars us a 14mm bolt.

 

G

GettinThere

Member

Jul 29, 2005

553

1

19

Central Texas

Jan 24, 2007

#3

• Jan 24, 2007

• #3

J&M Products said:

The difference between the 79-98 arms and the 99-04 arms is the bolt diameter, the 79-98 use a 12mm bolt and the 99-04 cars us a 14mm bolt.

Click to expand...

Yup. I found out the hard way with a set of Lakewood lca's. I ended up sending them back to Summit.

I wish the aftermarket parts companies would quit advertising lcas for 79-04 cars.

 

dastang2

Active Member

Dec 11, 2003

2,020

0

46

tx

Jan 24, 2007

#4

• Jan 24, 2007

• #4

why couldn't you just drill out the sleeves

 

G

GettinThere

Member

Jul 29, 2005

553

1

19

Central Texas

Jan 24, 2007

#5

• Jan 24, 2007

• #5

dastang2 said:

why couldn't you just drill out the sleeves

Click to expand...

I don't think that would have worked. I would rather get lcas that fit properly rather than modifying them to make them work. I should have gotten the MM ones to start with.

 

J&M Products

Premium Sponsor

Jan 22, 2007

62

10

29

Paso Robles

Jan 24, 2007

#6

• Jan 24, 2007

• #6

If you could pull the sleeves out of the bushings you should be able to put them in a lathe and drill them out. You might want to call the LCA manufacture and see if they will just sell you the inner sleeves for the 99-04. We sell them for our arms.

 

dastang2

Active Member

Dec 11, 2003

2,020

0

46

tx

Jan 24, 2007

#7

• Jan 24, 2007

• #7

will the stock sleeves for th 99-04 come out and fit on the aftermarket lca bushings

 

J&M Products

Premium Sponsor

Jan 22, 2007

62

10

29

Paso Robles

Jan 24, 2007

#8

• Jan 24, 2007

• #8

The stock sleeves are bonded to the rubber bushings. Different manufacutres use different size outside diameter sleeves depending on the bushings they are using. I would suggest calling the company who made the lca's or get new lca's all together. Those lower arms may not even be the right ones for your application. I would only use those arms on a drag car. The bushing combination will induce bind during cornering and will be hard on your torque boxes. That is why we came out with our Patent Pending Poly-Ball bushing setup.

 

1low03gt

20+ Year Stangneter

May 24, 2004

708

11

38

Cold Hell,Ontario,Canada!!

Jan 24, 2007

#9

• Jan 24, 2007

• #9

I got a set of upper ,and lowers used(but never installed in a stang,off of a buddy),and the lowers didn't fit do to the reason in bolt size mention above.So i drilled out the inner sleaves out of the stock lower control arms,and pushed out the sleeves out of the aftermarket lowers,then drilled the holes larger to fit the inner sleeves from the stock lowers. And on my way i went.