Anybody using NOS-02117 under their STOCK hood ?

Stangfreak95 · Dec 26, 2003

This is the 150shot plate kit that fits the Edelbrock Performer. Since I dont have my Performer installed yet and that my engine is out, there's no way that I could check the clearance myself. The plate is 1/2 inch thick.

I know that the Performer is higher from the start. Is there anybody that has tried this himself and knows that it fits/doesnt fit UNDER STOCK HOOD with the plate kit ??

Thanks
Mario

Rootus · Dec 26, 2003

Well, I barely clear the stock hood with my performer intake, had to actually remove insulation from the hood. I don't think it would fit if I put 1/2" spacer below it.

Dave

Stangfreak95 · Dec 26, 2003

HairyCanary said:
Well, I barely clear the stock hood with my performer intake, had to actually remove insulation from the hood. I don't think it would fit if I put 1/2" spacer below it.

Dave

I never had the insulation stuff anyway.
Thanks Dave. You always climb in to help me.

I've heard a lot of " I dont think it would fit" kinda stuff, but I need to find somebody that has tried this. I want to be sure.

Or somebody that is willing to simulate the situation by placing a 1/2 something on their upper Edelbrock Performer and try to close the hood with it and confirm this.

God, somebody must of tried this before !

Rootus · Dec 26, 2003

Gee, you didn't have to put it in big letters...

I put a lump of clay on the front corner of the intake and then dropped the hood on it. Came out with about 1/16" more than 1/2" of clearance. I could probably sneak in 1/2" spacer on my setup, but it would be damn close. I'd say close enough that you'd want to try it on your setup first -- it doesn't leave much room for variation from motor mounts, etc.

Dave

Stangfreak95 · Dec 26, 2003

HairyCanary said:
Gee, you didn't have to put it in big letters...

I wanted to get some attention hehe

HairyCanary said:
it doesn't leave much room for variation from motor mounts, etc.

Thats a good point. I need to get some new ones as well.
Still pretty tempting though.. Pretty much the cleanest and propably of the most efficient nitrous setups out there.

Thanks again for your help.
Mario

Rootus · Dec 26, 2003

How about the NX plate kit (part# 20102)? I can't find any detailed info on it. Probably 1/2" as well, but maybe it's thinner...

Dave

Stangfreak95 · Dec 26, 2003

HairyCanary said:
How about the NX plate kit (part# 20102)? I can't find any detailed info on it. Probably 1/2" as well, but maybe it's thinner...

Dave

Way to expensive for now

Buying so much stuff lately. I'll be ordering parts every week till summer I think. Cant spend all that on a nitrous kit. The 05115-II would do a good job as well.

Anybody using NOS-02117 under their STOCK hood ?

Stangfreak95

add a 4

Rootus

Officially Addicted

Stangfreak95

add a 4

Rootus

Officially Addicted

Stangfreak95

add a 4

Rootus

Officially Addicted

Stangfreak95

add a 4

Similar threads

Anybody using NOS-02117 under their STOCK hood ?

Stangfreak95

add a 4

Rootus

Officially Addicted

Stangfreak95

add a 4

Rootus

Officially Addicted

Stangfreak95

add a 4

Rootus

Officially Addicted

Stangfreak95

add a 4

Similar threads

Privacy & Transparency

Privacy & Transparency