• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Anyone ever get a bad Melling Oil pump before?? LONG Story inside

  • Thread starter Thread starter 1987stangman
  • Start date Start date Oct 19, 2008

1987stangman

Member
Jul 12, 2006
684
24
19
Oct 19, 2008
#1
  • Oct 19, 2008
  • #1
Hi everyone. Now that I have my car running and this mess behind me I wanted to throw this out and see how common it is to get a defective oil pump off the shelf and to VENT a little because I am still a tad pissed off about it. To make a seemingly endless story short I will get right to it. I pulled the motor about 2 months ago to rebuild it. I am lucky to also live less than a mile from Thumper Performance so I sent the heads to him to get ported and rebuilt and by the time he was done I was done with the short block and everything was reassembled and the motor was put back into the car. Before I fired it up for the first time I primed the pump with a drill to make sure everything had oil flowing to it. I also had primed it on the stand with a valve cover off prior to installing the upper intake manifold. Motor started right up and idled pretty good, no smoke at all and rings seemed to seat instantly and I had my wife watch the oil and temp gauges while I whipped out the timing light and timed it to 10 deg (for now). I let the motor sit and run for 15 or so min and I noticed the oil pressure dropped quick to ZERO and back up as if someone pulled the sending units wire and put it back on really fast. It did this 3 times and stopped and I thought it strange but it never did it again until I took the car for a spin around the block. I was lucky because as soon as I pulled into the driveway the gauge hit ZERO and stayed. I was pissed so I put it in the garage for the day and worked on it the next. Drained the oil expecting to find some copper from a wiped bearing but found nothing, I even drained it though an auto paint strainer. Pulled the filter and turned the pump shaft with a drill and it barley pushed oil and no oil would come out of the sending unit tube so it was official, bad pump. I was not looking forward to changing it in the car that was for sure but I spent all day Friday doing it. It really sucked but the reward was that the new pump is working great and it seems that no engine damaged occurred, but I only have like 100 miles on it. I was just going to return the pump and get my money back since I already bought a new one from Napa but I e-mailed Milling and explained the situation and they are requesting I send the defective pump back to them.

I know this post was long but getting the oil pump out of a Fox with it in the car is a real PITA!!!
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Oct 19, 2008
#2
  • Oct 19, 2008
  • #2
Non-technical issue - moved to 5.0 Talk.

Man, that sounds like a nightmare. I swear if I ever have an oil pump go bad, the engine is coming out. No way I'm laying on the ground under the car with oil dripping all over me, so I can change out the pump.
 

68stang351

Founding Member
May 16, 2002
850
9
39
Savoy TX
Oct 20, 2008
#3
  • Oct 20, 2008
  • #3
I had one seize one time. It had been in the car several years though. Twisted up the oil pump shaft and broke it. The car is so loud that I had no idea it happened until I got home, I think I drove 3 or 4 miles before I heard it rattling.
I also changed mine in the car, not fun! The motor was ok after that except it would rattle for about 2 seconds on a cold start. It was fine for a year or two, then it started getting worse and worse. I ended up taking it out and putting another motor in. The old one needs a new crank now. A guy wanted to buy it from me the other day for 100$, I think I'll sell it to him.
 
You must log in or register to reply here.

Similar threads

Fox won't crank over and fuel pump won't kick on.
  • djj62478
  • Jun 7, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
361
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 11, 2026
General karthief
H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
304
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
B
water pump installation questions
  • B0udreaux
  • Feb 5, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
38
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 28, 2026
General karthief
S
Fox '87 GT can't get to stay running
  • spilly
  • Mar 29, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
27
Views
837
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 20, 2026
spilly
S
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
273
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?