• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

aod to t5

  • Thread starter Thread starter izzleon
  • Start date Start date Sep 20, 2007
I

izzleon

New Member
May 7, 2007
22
0
0
Sep 20, 2007
#1
  • Sep 20, 2007
  • #1
hey whats up guys well im here to get some info on the swap.....but none have info of where i can get the bolts....i have everything for the swuap except the bolts.. no do i need to use the same crossmember? how about the shifter area is there any cutting?help would be verry well ppreciated...thanx
 

Mustang_Punk

Founding Member
Jan 15, 2002
224
0
0
Sac, Ca
Sep 20, 2007
#2
  • Sep 20, 2007
  • #2
you can reuse the bolts you have, you just need to cut the top 2 to fit, as for the crossmember I just used the one outta my wrecked 'vert
 

SVT32VDOHC

waiting for the next hack atta
Founding Member
Nov 22, 2001
3,501
28
119
Motor City
Sep 20, 2007
#3
  • Sep 20, 2007
  • #3
The crossmembers are the same. You will need the transmission harness. it starts at the left kick panel and goes through the trans tunnel to the trans. You also must cut the front of the hole in the floor out about an inch or so to get the front of the shifter to clear. With a buddy and all the right parts you can swap it in an afternoon.
 
B

BYRDPE

Founding Member
Nov 4, 1998
1,556
0
37
Memphis,Tn.
Sep 20, 2007
#4
  • Sep 20, 2007
  • #4
Don't alter the shifter area until you get ready to install the tranny.
By doing so you will know exactly how much to cut and hammer.
 

wythors

Get off my lawn!!!
Founding Member
May 17, 2000
2,277
35
69
C Addle
Sep 20, 2007
#5
  • Sep 20, 2007
  • #5
The two upper bolts get replaced with 7/16" x 1.5" coarse thread bolts. I got them out of the Dorman selection in my local auto parts store for .93 each.
 
V

v8only

Active Member
Jul 3, 2003
2,378
22
49
Sep 21, 2007
#6
  • Sep 21, 2007
  • #6
if you're lazy, just put washers on the top two bell bolts and be done with it. You'll never see it.

don't re use your old flywheel bolts, they're shorter. Get the arp flywheel bolts from summitracing or brothers...only $10.

as well, get the ford racing pressure plate bolt kit.

as for the bell to trans bolts, that should come with the trans you buy, if not, take the bell into the hardware store, and buy some nice bolts for it there.

the x member will likely bolt right in from your aod car, but you may have to cut/grind the welds off of the tubes on the left and right side of the x member. this allows the tubes to slide forward and back to adj for x member positioning. Again though, I've never had an issue using the aod piece.
 
You must log in or register to reply here.

Similar threads

H
Drivetrain 6R80 to t56 swap
  • Holymoses
  • Apr 25, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
427
Fox 5.0 Mustang Tech Apr 25, 2026
AeroCoupe
R
Engine Evap and charcoal cannister leak
  • ryan1994stang
  • Mar 14, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
660
Fox 5.0 Mustang Tech Mar 18, 2026
Mcmahst
N
Engine 86 GT no start/stall
  • nweber
  • Jul 28, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
278
Fox 5.0 Mustang Tech Jul 29, 2026
AeroCoupe
K
3.8 T5 & Bellhousing to 1987 Lincoln 5.0
  • ks65stang
  • Mar 2, 2026
  • Other Auto Tech
Replies
3
Views
565
Other Auto Tech Mar 3, 2026
Noobz347
G
Resolved Smoking Wiring Issue After GT40 Head Swap
  • Grapes
  • Aug 15, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
599
Fox 5.0 Mustang Tech Aug 22, 2026
Grapes
G
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?