• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

BAD steering rack : suggestions?

  • Thread starter Thread starter STANG#5
  • Start date Start date Mar 21, 2006

STANG#5

Founding Member
Apr 24, 2001
179
0
0
KC
Mar 21, 2006
#1
  • Mar 21, 2006
  • #1
I just installed a D&D k- member w/ control arms & coil-overs. Thought this would be a good time to change out the worn out rack. I considered the 15:1 manual rack from Flaming River, but w/ 275/40/17's out front, I think it'll be a little to tough to steer at slow speeds. So, do I put in a Ford rack or something else?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 21, 2006
#2
  • Mar 21, 2006
  • #2
Ford PS rack and save the workout for the gym... Unless you are the big guy who turns green & mean in traffic...

The two inner tie rod ends are usually what wears out, and at $45 each, it's better to get a replacement rack assembly since they are part of the package. The rack is about $100 + a $40 refundable core charge, which you get back when you return the old rack. Be sure to ask for the GT or high performance rack, it has fewer turns lock to lock than the standard rack.

The flex coupling for the steering shaft needs to be disconnected before you can get the rack out. You should disassemble the coupling by undoing the 2 bolts that hold it together. The lower part of the coupling will then come out with the rack, and can easily be removed.

The tie rod ends can be removed with a tool that looks like a giant "pickle fork", it's less than $8, or some stores will rent/loan one. Remove the cotter pin & nut on the tie end, stick the tool between the rod end and the arm it connects and hammer away. The bigger the hammer, the easier it comes apart.

Remove the two bolts that bolt the rack assembly to the frame and then pull the rack down. Get a catch pan to dump the fluid in when you disconnect the hydraulic lines. I replaced the rack mount bushings with some Energy Suspension urethane ones. When you re-install the rack assembly, put the rear bushings in the rack assembly and lift it into place. Then install the front bushings & washers and tighten down the nuts. Doing it this way makes room for the hydraulic lines without having them bind against the frame.

To change the tie rod ends, do them one at a time. Loosen the jam nut 1/4 turn, then unscrew the tie rod end from the rack. Turn the jam nut back 1/4 turn to return it to its original position. With the tie rod end removed, use a machinist square to measure the distance between the end of the threaded rod and the jam nut. Sit the bottom of the square against the end of the threaded rod, and the end of the blade of the square against the jam nut. Duplicate the measurement on the new rack and then install the tie rod end and tighten the jam nut. Then do the other side: the front end will need aligning, but the toe in will be close enough to the setting of the original rack to drive.

Buy several extra quarts of fluid to run through the system to flush it when you change the rack. The car needs to be up on jackstands for the next step. Fill the pump up, start the car, and turn the wheels lock to lock to bleed the air out. Then stop the engine, disconnect the low pressure hose (the one that is secured with a hose clamp) and drain the pump. Re-connect, refill and do it several more times or until the fluid looks clear and not burnt or black.
 

STANG#5

Founding Member
Apr 24, 2001
179
0
0
KC
Mar 21, 2006
#3
  • Mar 21, 2006
  • #3
By doing it while I'm changing the motor & k-member, the hard part is done. I think I'm going to go ahead w/ the Fod rack though
 
You must log in or register to reply here.

Similar threads

B
Rack and pinion options
  • Bronco Bart
  • Sep 7, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
18
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 13, 2025
AeroCoupe
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
491
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
New to me 98 Cobra
  • bird_dog0347
  • Feb 25, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • 2
Replies
26
Views
2K
1996 - 2004 SN95 Mustang -General/Talk- Mar 24, 2026
FastDriver
SOLD SOLD!!!! 1993 Notchback Roadracer For Sale. She's a beast!
  • Boydster
  • Apr 25, 2025
  • Fox Body Mustangs For Sale (1979-93)
Replies
0
Views
1K
Fox Body Mustangs For Sale (1979-93) Apr 25, 2025
Boydster
B
Where to go from here on my build…
  • B0udreaux
  • Jul 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
468
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 18, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?